STK500_2下载器 M8 支持bootloader(带bootloader源码) 使用STK500_2 协议的ISP下载器，监控芯片 M8,数据通讯RS232.使用 ATMEL AVRStudio 4.xx STK500工具的进行软件升级。可通过ATMEL AVRStudio 4.xx STK500工具升级固件程序。升级方法：通过设定电压 即按“write voltage”按钮进入bootloader程序。
标签： bootloader STK 500 ISP
上传时间： 2014-08-27
上传用户：haoxiyizhong
This directory contains example ADSPBF535 code, written in assembly, that changes the frequency and voltage using the push button switches on the board.
标签： directory frequency contains assembly
上传时间： 2014-01-03
上传用户：evil
A new cable fault location method based on wavelet reconstruction is proposed. In this method the difference between the currents of faulty phase and sound phase under the high voltage pulse excitation is used as the measured signal and is decomposed in multi-scale by wavelet transform, then reconstructed in single scale. Comparing with traditional fault location method by travelling wave, the presented method will not be interfered by the reflected wave from the branch joint of cables or from other positions where the impedances are not matched and not be influenced by fault types, otherwise, the reflected waves can be recognized even the faulty position is near to the measuring terminal, at the same time, the influence of the wave speed uncertainty can be reduced. The correctness of the proposed method is proved by simulation results.
标签： method reconstruction location proposed
上传时间： 2016-02-04
上传用户：maizezhen
16 relay output channels and 16 isolated digital input channels LED indicators to show activated relays Jumper selectable Form A/Form B-type relay output channel Output status read-back Keep relay output values when hot system reset High-voltage isolation on input channels(2,500 VDC) Hi ESD protection(2,00VDC) High over-voltage protection(70VDC) Wide input range(10~50VDC) Interrupt handling capability High-density DB-62 connector Board ID
标签： channels indicators activated isolated
上传时间： 2016-02-15
上传用户：dongbaobao
（1）变换模块 本模块包含两部分内容：利用 反变换规则将 坐标系下的两相电流转换成三相电流；利用间接矢量控制，得到转子角位移，公式如下（2） 电流滞环控制器(Hysteresis current controller)模块（3） 电压源型逆变器(Voltage sourse inverter,VSI)模块 （4） 变换模块（5） 感应电机(IM)模块 该感应电机模型是基于交流电机的电路方程、转矩方程以及运动方程建立起来的。该仿真模块为一个三输入、六输出的系统子模块。输入为 坐标系中定子电压，输出则是 坐标系中的转子电流和转子磁链，以及输出的转矩。（6） 电流反馈模块（7）速度控制器模块
上传时间： 2014-03-10
上传用户：yy541071797
：介绍了一种基于数字信号处理器（DSP）的移相调频（Phase-Shifted and Frequency-Varied，PSFV）PWM控制 逆变电源，给出了主电路拓扑结构，分析了其控制原理并设计了其控制程序流程图。新颖的PSFV 控制能够实现输出 电压90％的调整率，输出电流波动小于单纯移相调功PWM方式，并在轻载时保持连续。功率开关器件零电压零电流 通断（Zero-Voltage-Zero-Current Switching，ZVZCS）软开关的实现，有利于进一步提高开关频率和降低开关损耗。采用 高性能的专用DSP 芯片TMS320F2812 实现了系统的数字控制，满足了系统控制的灵活性和实时性，减小了系统的 体积和生产成本。仿真分析和实验结果证明了此控制模式的可行性与合理性。
标签： Frequency-Varied Phase-Shifted DSP and
上传时间： 2013-12-04
上传用户：kristycreasy
This example demonstrates the use of the ADC block and PWM blocks. The generated DSP code produces the pulse waveform whose duty cycle is changing as the voltage applied to ADC input changes. The waveform period is kept constant.
标签： demonstrates the generated produces
上传时间： 2016-05-17
上传用户：sjyy1001
电力电子环流SIMULINK模型 Notice that the Thyristor blocks have an output identified by the letter m. This output returns a Simulink vectorized signal containing the thyristor current (Iak) and voltage (Vak).
标签： m. identified Thyristor the
上传时间： 2013-12-13
上传用户：水中浮云
本装置是一个以HT46R71D 为主芯片，配合传感器组成的汽车轮胎气压检测装 置，最终取高三位有效值于LCD 显示，有四种显示单位供切换（Psi、Bar、Kpa、 Kgf/cm2）。本装置仅为参考范例，使用时，为提高准确度，建议多量测些组数 据来构建Sensor Output Voltage - Discharge Time (V-T)表格，并作相应校准。
上传时间： 2014-01-14
上传用户：cxl274287265
The FM24C256/C256L/C256LZ devices are 256 Kbits CMOS nonvolatile electrically erasable memory. These devices offer the designer different low voltage and low power options. They conform to all requirements in the Extended IIC 2-wire protocol. Furthermore, they are designed to minimize device pin count and simplify PC board layout requirements.
标签： 256 electrically nonvolatile erasable
上传时间： 2016-12-11
上传用户：lps11188
