虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

three-input

  • PCA954X家庭的I C SMBus多路复用器与开关

    The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.

    标签: SMBus 954X PCA 954

    上传时间: 2013-10-11

    上传用户:dianxin61

  • Using the P82B96 for bus inter

    The P82B96 offers many different ways in which it can be used as abus interface. In its simplest application it can be used as aninterface between bus systems operating from different supplyvoltages. Opto isolation between two bus systems is possible, andalso the availability of the Tx and Rx signals permits interfacing ofthe P82B96 with other bus systems which separate the forwardoutput path, from the backward input signal path.

    标签: P82B96 Using inter the

    上传时间: 2013-10-11

    上传用户:洛木卓

  • 16-bit IC and SMBus I/O Port w

    The CAT9555 is a CMOS device that provides 16-bitparallel input/output port expansion for I²C and SMBuscompatible applications. These I/O expanders providea simple solution in applications where additional I/Osare needed: sensors, power switches, LEDs,pushbuttons, and fans.

    标签: SMBus Port bit and

    上传时间: 2014-01-09

    上传用户:1101055045

  • 8-bit IC and SMBus IO Port wit

    The CAT9534 is an 8-bit parallel input/output portexpander for I²C and SMBus compatible applications.These I/O expanders provide a simple solution inapplications where additional I/Os are needed: sensors,power switches, LEDs, pushbuttons, and fans.The CAT9534 consists of an input port register, anoutput port register, a configuration register, a polarityinversion register and an I²C/SMBus-compatible serialinterface.

    标签: SMBus Port bit and

    上传时间: 2013-11-09

    上传用户:liulinshan2010

  • 基于8086 CPU 的单芯片计算机系统的设计

    本文依据集成电路设计方法学,探讨了一种基于标准Intel 8086 微处理器的单芯片计算机平台的架构。研究了其与SDRAM,8255 并行接口等外围IP 的集成,并在对AMBA协议和8086 CPU分析的基础上,采用遵从AMBA传输协议的系统总线代替传统的8086 CPU三总线结构,搭建了基于8086 IP 软核的单芯片计算机系统,并实现了FPGA 功能演示。关键词:微处理器; SoC;单芯片计算机;AMBA 协议 Design of 8086 CPU Based Computer-on-a-chip System(School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China)Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification

    标签: 8086 CPU 单芯片 计算机系统

    上传时间: 2013-12-27

    上传用户:kernor

  • 高压双管反激变换器的设计

    高压双管反激变换器的设计:介绍一种双管反激的电路拓扑,分析了其工作原理,给出了一些关键技术参数的计算公式,设计并研制成功的30W 380V AC5 0H z/510V DC/+15.1 V DC(1A )、+5.2VDC(2A)辅助开关电源具有功率密度高、变换效率高、可靠性高等优良的综合性能。该变换器在高电压输人情况下有重要的应用价值。【关 键 词 】变换器,辅助开关电源,双管反激 [Abstract】 A n e wt opologyfo rd oubles witchfl ybackc onverteris in troduced.Th eo perationp rincipleis a nalyzeda nds ome for mulas for calculating key parameters for the topology are presented. The designed and produced auxiliary switching power supply,i. e. 30W 380V AC5 0H z/5 10V DC/+15.1 V DC《1A )、+5.2 V DC《2A ),hase xcellentc omprehensivep erformances sucha sh ighp owerd ensity, hi ghc onversione fficiencya ndh ighr eliability.Th isc onverterh asim portanta pplicationv aluef orh igh input voltag [Keywords ]converter,au xiliary switchingp owers upply,do ubles witchf lybac

    标签: 双管反激 变换器

    上传时间: 2013-11-01

    上传用户:Ants

  • 水位监测报警系统原理

    摘要:本水位监测报警器使用5V低压直流电源(也可以用3节5号电池代替)就可以对5~15厘米的水位进行监测,用LED显示和数码管显示水位,并可以对不再此范围内的水位发出报警。主要采用CD4066、74LS86、74LS32、CD4511芯片,再加上数码管、蜂鸣器、发光二极管、电阻这些器件组成一个简单而灵敏的监测报警电路,操作简单,接通电源即可工作。因为大部分电路采用数字电路,所以本水位监测报警器还具有耗能低、准确性高的特点。关键字:译码电路    报警电路    监测电路 Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics. Keyword: Decoding circuit alarm circuit monitoring circuit

    标签: 水位 监测报警 系统原理

    上传时间: 2013-11-05

    上传用户:王庆才

  • An easy way to work with Exter

    Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.

    标签: Exter easy work with

    上传时间: 2013-10-27

    上传用户:zhangyigenius

  • 用外部设备设置32位微控制器TriCore的中断的指令及方法

    The Infineon TriCore provides an Interrupt System with a high safety standard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps

    标签: TriCore 外部设备 中断 微控制器

    上传时间: 2013-11-05

    上传用户:uuuuuuu

  • 介绍C16x系列微控制器的输入信号升降时序图及特性

    All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.

    标签: C16x 微控制器 输入信号 时序图

    上传时间: 2014-04-02

    上传用户:han_zh