Many telecommunications and computing applicationsneed high effi ciency step-down DC/DC converters thatcan operate from a very low input voltage. The highoutput power synchronous controller LT3740 is idealfor these applications, converting input supplies rangingfrom 2.2V to 22V to outputs as low as 0.8V with loadcurrents from 2A to 20A. Applications include distributedpower systems, point-of-load regulation and conversionof logic supplies.
上传时间： 2013-11-05
上传用户：zhf01y
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
The LTC®4151 is a high side power monitor that includesa 12-bit ADC for measuring current and voltage, as wellas the voltage on an auxiliary input. Data is read throughthe widely used I2C interface. An unusual feature in thisdevice is its 7V to 80V operating range, allowing it to coverapplications from 12V automotive to 48V telecom.
上传时间： 2013-10-29
上传用户：集美慧
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
One of the fi rst lessons in a basic electronics coursecovers the symbols for resistors, capacitors, inductors,voltage sources and current sources. Althougheach symbol represents a functional component of areal-world circuit, only some of the symbols have directphysical counterparts. For instance, the three discretepassive devices—resistors, capacitors, inductors—canbe picked off a shelf and placed on a real board muchas their symbolic analogs appear in a basic schematic.Likewise, while voltage sources have no direct 2-terminalanalog, a voltage source can be easily built with an offthe-shelf linear regulator.
上传时间： 2013-11-24
上传用户：simonpeng
AN22 details the theoretical and application aspects of the LT1088 thermal RMS/DC converter. The basic theory behind thermal RMS/DC conversion is discussed and design details of the LT1088 are presented. Circuitry for RMS/DC converters, wideband input buffers and heater protection is shown.
上传时间： 2013-10-16
上传用户：china97wan
In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (see separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
上传时间： 2013-10-30
上传用户：yeling1919
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
