虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

internally

  • The LM158 series consists of two independent, high gain, internally frequency compensated operatio

    The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.

    标签: compensated independent internally frequency

    上传时间: 2014-01-09

    上传用户:zwei41

  • design LP,HP,B S digital Butterworth and Chebyshev filter. All array has been specified internally

    design LP,HP,B S digital Butterworth and Chebyshev filter. All array has been specified internally,so user only need to input f1,f2,f3,f4,fs(in hz), alpha1,alpha2(in db) and iband (to specify the type of to design). This program output hk(z)=bk(z)/ak(z),k=1,2,..., ksection and the freq.

    标签: Butterworth internally Chebyshev specified

    上传时间: 2015-11-08

    上传用户:253189838

  • SN65LBC170,SN75LBC170,pdf(TRIP

    The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.

    标签: 170 LBC SN TRIP

    上传时间: 2013-10-13

    上传用户:ytulpx

  • CAT25128-128Kb的SPI串行CMOS EEPRO

    The CAT25128 is a 128−Kb Serial CMOS EEPROM device internally organized as 16Kx8 bits. This features a 64−byte page write buffer and supports the Serial Peripheral Interface (SPI) protocol. The device is enabled through a Chip Select (CS) input. In addition, the required bus signals are clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input may be used to pause any serial communication with the CAT25128 device. The device featuressoftware and hardware write protection, including partial as well as full array protection.

    标签: 25128 EEPRO CMOS CAT

    上传时间: 2013-11-15

    上传用户:fklinran

  • Input Signal Rise and Fall Tim

    All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.

    标签: Signal Input Fall Rise

    上传时间: 2013-10-23

    上传用户:copu

  • 介绍C16x系列微控制器的输入信号升降时序图及特性

    All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.

    标签: C16x 微控制器 输入信号 时序图

    上传时间: 2014-04-02

    上传用户:han_zh

  • SL811开发资料_包含源程序_电路图_芯片资料

    SL811开发资料_包含源程序_电路图_芯片资料:SL811HS Embedded USB Host/Slave Controller.The SL811HS is an Embedded USB Host/Slave Controller capable of communicate with either full-speed or low-speed USB peripherals. The SL811HS can interface to devices such as microprocessors, microcontrollers, DSPs, or directly to a variety of buses such as ISA, PCMCIA, and others. The SL811HS USB Host Controller conforms to USB Specification 1.1.The SL811HS USB Host/Slave Controller incorporates USB Serial Interface functionality along with internal full-/low-speed transceivers.The SL811HS supports and operates in USB full-speed mode at 12 Mbps, or at low-speed 1.5-Mbps mode.The SL811HS data port and microprocessor interface provide an 8-bit data path I/O or DMA bidirectional, with interrupt support to allow easy interface to standard microprocessors or microcontrollers such as Motorola or Intel CPUs and many others. internally,the SL811HS contains a 256-byte RAM data buffer which is used for control registers and data buffer.The available package types offered are a 28-pin PLCC (SL811HS) and a 48-pin TQFP package (SL811HST-AC). Both packages operate at 3.3 VDC. The I/O interface logic is 5V-tolerant.

    标签: 811 SL 开发资料 源程序

    上传时间: 2013-12-22

    上传用户:a82531317

  • TIMER.ASM ********* [ milindhp@tifrvax.tifr.res.in ] Set Processor configuration word as = 000

    TIMER.ASM ********* [ milindhp@tifrvax.tifr.res.in ] Set Processor configuration word as = 0000 0000 1010 b. a] -MCLR tied to VDD (internally). b] Code protection off. c] WDT disabled. d] Internal RC oscillator [4 MHZ].

    标签: configuration Processor milindhp tifrvax

    上传时间: 2015-05-24

    上传用户:wqxstar

  • This book explains how to write device drivers for the newest members of the MicrosoftWindows family

    This book explains how to write device drivers for the newest members of the MicrosoftWindows family of operating systems using the Windows Driver Model (WDM). In this Introduction, I ll explain who should be reading this book, the organization of the book, and how to use the book most effectively. You ll also find a note on errors and a section on other resources you can use to learn about driver programming. Looking ahead, Chapter 1 explains how the two main branches of the Windows family operate internally, what a WDM device driver is, and how it relates to the rest of Windows.

    标签: MicrosoftWindows the explains drivers

    上传时间: 2014-01-04

    上传用户:dongqiangqiang

  • Next+Generation+Telecommunications+Networks

    Never have telecommunications operations and network management been so important. Never has it been more important to move away from practices that date back to the very beginning of the telecommunications industry. Building and con- necting systems internally at low cost, on an as - needed basis, and adding software for supporting new networks and services without an overall architectural design will not be cost effective for the future. Defi ning operations and network manage- ment requirements at the 11th hour for new technologies, networks, and services deployments must also change. 

    标签: Telecommunications Generation Networks Next

    上传时间: 2020-05-31

    上传用户:shancjb