Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V Input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide Input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
标签： MAXREFDES Lakewood Isolated Output
上传时间： 2013-11-02
上传用户：fengzimili
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V Input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide Input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
标签： Riverside MAXREFDES Isolated Output
上传时间： 2013-11-16
上传用户：会稽剑客
When a system designer specifies a nonisolated dc/dc powermodule, considering the needed Input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide Input voltage range. NarrowInputmodules typically have a nominal Input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated Input bus—such as those that do not use batterybackup—a narrow-Input module is often adequate sincethe Input remains fairly stable.Offering greater flexibility, wide-Input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-Input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-Inputdc/dc modules.
标签： Wide-Input modules offer dc
上传时间： 2014-12-24
上传用户：dragonhaixm
All Inputs of the C16x family have Schmitt-Trigger Input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these Inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling Input transitions.Thus, it must be taken care that rising/falling Input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock Inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the Input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allInput signals are evaluated at specific sample points (depending on the Input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an Input signalat these sample points is relevant, that means, the necessary rise/fall times of the Inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an Input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which Input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For Inputs which are connected to a peripheral function, e.g. capture Inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresInput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For Input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the Inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
Award BIOS(Basic Input/Output System)(电脑启动时所必需)的源码
上传时间： 2014-01-04
上传用户：ecooo
This program can determin very accurately the nature of the user Input
标签： accurately the determin program
上传时间： 2015-01-28
上传用户：shinesyh
生成BCD码。 Name: BIN3toBCD4 Func:2字节二进制整数--->>BCD码四字节转换(Comped BCD) Input: 3进制数人低字节到高字节存放在内部RAM50H，51H,52h单元中 Output: BCD码人低位到高位分别存放在内部RAM53H,54H，55H，56H单元中 USE: R7-R0, 56H-50H
标签： BCD BIN3toBCD4 Comped Input
上传时间： 2015-02-02
上传用户：FreeSky
The VideoTransmit class is a simple wrapper that can be programmed to take video Input from a source of your choice and transmit the video to a destination computer or network in JPEG format.
标签： VideoTransmit programmed wrapper simple
上传时间： 2014-01-06
上传用户：zhuyibin
The audioTransmit class is a simple wrapper that can be programmed to take audio Input from a source of your choice and transmit the audio to a destination computer
标签： audioTransmit programmed wrapper simple
上传时间： 2013-12-16
上传用户：sjyy1001
词法分析器：源程序的运行方式： 运行程序 输入一个已存在的文本文档的文件名。如：Input.txt 如果要对整个程序进行语法分析，则按‘y’键，否则按‘n’键 如果要对程序进行语法分析，则按‘y’键，否则按‘n’键 程序结束
上传时间： 2014-01-22
上传用户：zhaiyanzhong
