针对51单片机系统中常用的A/D转换器价格高、精度低的缺点,介绍TI公司的16 位的带有I2C串行接口的A/D转换器ADS1110的工作原理,给出ADS1110与AT89C51单片机系统的接口电路和软件设计。实践证明,ADS1110具有高性价比和实用性。 Abstract: According to the disadvantages of high expense and low accuracy of the general A/D converter used in MCS51 microchip system,the principle and working process of a high accuracy 16-bit A/D conversion ADS1110 which has I2C bus and belongs to TI Company are proposed here as well as the interface of ADS1110 to AT89C51 and software list.It is proved to be high performance index and practicability.
上传时间: 2013-11-21
上传用户:gyq
基于CC1110单片机公交报站系统主要由CC1110单片机最小系统和WT588D语音模块组成,提出了如何实现语音报站,通过无线通信SimpliciTI网络协议实现公交站台的自动播报和OLCD液晶显示公交运行的各类信息。结果表明,该公交报站系统报站准确率99%,价格比同类产品下降了300%以上,系统组成结构简单,提高了系统的抗干扰性和稳定性,也便于携带。 Abstract: The bus stop announcement system based on CC1110 MCU is composed of CC1110 MCU minimum system and WT588D voice module. How to achieve the voice announcing is put forward.The bus-stop will announce automatically and display on the OLCD by means of wireless communication SimpliciTI network protocol. As a result, the bus station stop announcement systems reported 99% accuracy rate, price of similar products declined by 300% or more, system of simple structure, improve the anti-jamming and stability of the power system, it is also portable.
上传时间: 2013-10-21
上传用户:baby25825
通过对程控滤波器的理论分析,在研究MAX262的功能和单片机的SPI总线通信的基础上,提出了基于MAX262的程控滤波器设计方案,设计了程控滤波器的软硬件,并给出了测试结果。 Abstract: By analyzing the programmable filter,the paper puts forward a programmable filter system design based on MAS262 on basic of studying MAS262 features and SPI bus communication.Software and hardware of the programmmable filter are designed,and the test result is given.
上传时间: 2013-11-15
上传用户:wxhwjf
针对目前采用的热敏电阻测量方法,提出了采用单总线数字式温度传感器DS18B20和单片机组成的新型温度测量仪。介绍DS18B20的结构和工作原理,以及单总线工作原理,给出了由Mega8单片机和DS18B20构成的单总线温度测量仪的硬件电路及软件流程图。经试验基于单总线器件DS18B20的温度测量仪,具有测量准确、测温范围宽、体积小、控制方便等优点。 Abstract: This paper brings forward a new temperature meter composed of 1-Wire temperature sensor DS18B20 and MCU which has advantage of the thermistor. In the article, the DS18B20's structure and controlling principles are introduced and hardware circuit and software diagram of the temperature meter are given.After been tested,the temperature meter has the advantages of accurate measurement, wide temperature range, small volume and convenient controlling.
上传时间: 2013-10-31
上传用户:hzy5825468
为深入了解基于UC3854A控制的PFC变换器中的动力学特性,研究系统参数变化对变换器中分岔现象的影响,在建立Boost PFC变换器双闭环数学模型的基础上,用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上,分析了系统参数变化对分岔点的影响,并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A, and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC (Power Factor Correction) converter controller was built. Then, with the help of Matlab, the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上传时间: 2013-10-17
上传用户:杜莹12345
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心,基于标准的USB1.1协议,设计一种通用USB接口模块,以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间: 2014-01-08
上传用户:赵云兴
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移,一般采用光电轴角编码器检测位置信号,输出正交编码脉冲信号。若采用其他方法检测位置信号,必然导致电路设计复杂,可靠性降低。因此,提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理,LS7266R1与单片机的接口硬件设计,以及主程序软件流程图。巧妙地把力量传感器,位移传感器等机械运动状态的压力或拉力以及位置坐标,变成了电压信号和电脉冲数字信号,供A/D测量和LS7266R1计数,从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore, the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods, will inevitably lead to the circuit design complexity, reliability decreased. The work theory of the controller, the hardware interface design between LS7266R1 and single chip, and the flow chart of main program, are presented in this paper. The signal of the compression or tension power and displacement at working, which tested by power sensor and displacement sensor especially, is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself, or controlled by the COM command of PC.
上传时间: 2013-11-02
上传用户:yl1140vista
介绍一种应用于长城赛弗SUV汽车后门车窗多功能控制器,能实现对电动玻璃车窗、车窗雨刮器、喷水器以及电加热除霜器等控制。介绍了基于NXP P89LPC922单片机多功能汽车后车窗控制器的控制功能、硬件电路原理和软件设计方法。 Abstract: This paper presents a multipurpose automotive rear windows controller for CHANGCHENG SAFE SUV.The controller can control rear power-operated window,rear wiping,washing water pump and rear defroster of the windows. In this paper, it is introduced in detail that the functions and the design of the circuit and program of the controller based on NXP P89LPC922 MCU.
上传时间: 2013-11-13
上传用户:z754970244
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础,介绍了网卡软件驱动程序的编制,给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上传时间: 2013-10-23
上传用户:xiehao13
主要介绍了以PIC18F2480单片机为处理器,基于可编程多路开关检测接口器件MC33993实现的车用多路开关检测接口电路的设计。该设计克服了以往基于分立元件的检测接口电路的弊端,简化了接口电路设计,保证了车用开关工作的可靠性和安全性。 Abstract: The design of automotive multiple switch detection interface circuit based on MC33993 is introduced mainly which adopts PIC18F2480 single chip microprocessor.This circuit overcomes shortage of traditional design which contains many schism elements, and the application of MC33993 also predigests the whole design of interface circuit and guarantees the dependability and security of the switch.
上传时间: 2013-11-19
上传用户:star_in_rain