All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
Applying power to a standard logic chip, SRAM, or EPROM, usually results in output pinstracking the applied voltage as it rises. Programmable logic attempts to emulate that behavior,but physics forbids perfect emulation, due to the device programmability. It requires care tospecify the pin behavior, because programmable parts encounter unknown variables – yourdesign and your power environment.
上传时间： 2013-11-24
上传用户：253189838
In this paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level simulation mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this paper, however,here we try to cover a few of them.
标签： Efficient Verilog Digital Coding
上传时间： 2013-11-23
上传用户：我干你啊
I have a dream that I am always young. Then I will have enough energy to do everything whenever I want. Moreover, I don t have to worry about the old age during which I even can t take care of myself
标签： have everything whenever always
上传时间： 2016-01-24
上传用户：whenfly
ExcpHook is an open source (see license.txt) Exception Monitor for Windows made by Gynvael Coldwind (of Team Vexillium). t uses a ring0 driver to hook KiExceptionDispatch procedure to detect the exceptions, and then shows information about the exception on stdout (using the ring3 part of the program ofc). The difference between this method, and the standard debug API method it that this method monitores all of XP processes, and the program does not have to attach to any other process to monitor it, hence it s harder to detect. The code currently is considered as ALPHA, and it has been reported to BSoD sometimes (on multi core/cpu machines). Take care!
标签： Exception ExcpHook Coldwind Monitor
上传时间： 2014-02-10
上传用户：jing911003
Squaring circuits are an important building block for impulse-radio UWB non-coherent receivers. This work proposes a squarer, based on the quadratic law of saturated transistors. Such a circuit has already been proposed for lower frequency applications, therefore this work focuses on the extension to ultra wide bandwidth, with particular care to the consequences related to the deviation from the ideal quadratic law of 0.18μm CMOS transistors.
标签： impulse-radio non-coherent important receivers
上传时间： 2013-12-24
上传用户：kikye
--- --- --- --- --- --- Visual Studio Project Renamer For Win9x/NT/2k By Niek Albers nieka@daansystems.com (C)2001 DaanSystems Homepage: http://www.daansystems.com ------------------------------------ Use with care and on your own risk! Make backups before you use this program. Do a rebuild all on your renamed project. Usage: vsrename <oldname> <newname> <dir> Where: oldname : The old name of your project (typically the xxx from xxx.dsw) newname : The new name for your project dir : The directory tree that holds the project. The program will replace all occurences of oldname to newname in all files and rename all filenames that have the old name in it. It will walk subdirectories.
标签： Project Renamer Visual Studio
上传时间： 2013-12-15
上传用户：13517191407
ieee投稿须知，The IEEE Transactions on Information Technology in Biomedicine publishes high quality applications & infrastructure papers that reflect global information technology advances in medicine and biology and will further address the implementation and management of the broad spectrum of health care innovations arising from these developments world-wide
标签： ieee
上传时间： 2016-08-29
上传用户：zhouli
Many of the designations used by manufacturers and sellers to distinguish their products are claimed as trademarks. Where those designations appear in this book and Addison Wesley Longman Inc., was aware of a trademark claim, the designations have been printed in initial caps or all caps. The authors and publisher have taken care in the preparation of this book, but make no expressed or implied warranty of any kind and assume no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages in connection with or arising out of the use of the information or programs contained herein. The publisher offers discounts on this book when ordered in quantity for special sales. For more information, please contact:
标签： manufacturers designations distinguish products
上传时间： 2017-01-23
上传用户：woshiayin
