虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

bpsk-and-ASK-Simulation

  • keil and proteus联合演示显示效果

    keil and proteus联合演示显示效果,可实现音乐的播放,对初学者比较有用;很好的例子

    标签: proteus keil and 显示效果

    上传时间: 2013-09-25

    上传用户:yangqian

  • Proteus simulation of graphical lcd

    Proteus simulation of graphical lcd

    标签: simulation graphical Proteus lcd

    上传时间: 2013-09-25

    上传用户:lyy1234

  • the practice of proteus and avr

    the practice of proteus and avr

    标签: practice proteus the and

    上传时间: 2013-09-29

    上传用户:tom_man2008

  • Verilog Coding Style for Efficient Digital Design

      In this paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level simulation mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this paper, however,here we try to cover a few of them.

    标签: Efficient Verilog Digital Coding

    上传时间: 2013-11-22

    上传用户:han_zh

  • Verilog编码中的非阻塞性赋值

      One of the most misunderstood constructs in the Verilog language is the nonblockingassignment. Even very experienced Verilog designers do not fully understand how nonblockingassignments are scheduled in an IEEE compliant Verilog simulator and do not understand whenand why nonblocking assignments should be used. This paper details how Verilog blocking andnonblocking assignments are scheduled, gives important coding guidelines to infer correctsynthesizable logic and details coding styles to avoid Verilog simulation race conditions

    标签: Verilog 编码 非阻塞性赋值

    上传时间: 2013-10-17

    上传用户:tb_6877751

  • 电台维修模拟训练系统设计方法研究

    Methods for designing a maintenance simulation training system for certain kind of radio are introduced. Fault modeling method is used to establish the fault database. The system sets up some typical failures, follow the prompts trainers can locate the fault source and confirm the type to accomplish corresponding fault maintenance training. A training evaluation means is given to examining and evaluating the training performance. The system intuitively and vividly shows the fault maintenance process, it can not only be used in teaching, but also in daily maintenance training to efficiently improve the maintenance operation level. Graphical programming language LabVIEW is used to develop the system platform.

    标签: 电台维修 模拟训练 方法研究 系统设计

    上传时间: 2013-11-19

    上传用户:3294322651

  • 使用LTC运算放大器宏模型

      This application note is an overview discussion of theLinear Technology SPICE macromodel library. It assumeslittle if any prior knowledge of this software library or itshistory. However, it does assume familiarity with both theanalog simulation program SPICE (or one of its manyderivatives), and modern day op amps, including bipolar,JFET, and MOSFET amplifier technologies

    标签: LTC 运算放大器 模型

    上传时间: 2013-11-14

    上传用户:zhanditian

  • 相敏检波电路鉴相特性的仿真研究

    分析了调幅信号和载波信号之间的相位差与调制信号的极性的对应关系,得出了相敏检波电路输出电压的极性与调制信号的极性有对应关系的结论。为了验证相敏检波电路的这一特性,给出3 个电路方案,分别选用理想元件和实际元件,采用Multisim 对其进行仿真实验,直观形象地演示了相敏检波电路的鉴相特性,是传统的实际操作实验所不可比拟的。关键词:相敏检波;鉴相特性;Multisim;电路仿真 Abstract : The corresponding relation between modulation signal polarity and difference phases of amplitudemodulated signal and the carrier signal ,the polarity of phase2sensitive detecting circuit output voltage and the polarity of modulation signal are correspondent . In order to verify this characteristic ,three elect ric circuit s plans are produced ,idea element s and actual element s are selected respectively. Using Multisim to carry on a simulation experiment ,and then demonst rating the phase detecting characteristic of the phase sensitive circuit vividly and directly. Which is t raditional practical experience cannot be com pared.Keywords :phase sensitive detection ;phase2detecting characteristic ;Multisim;circuit simulation

    标签: 相敏检波 电路 仿真研究 鉴相

    上传时间: 2013-11-23

    上传用户:guanhuihong

  • PCB Design Considerations and Guidelines for 0.4mm and 0.5mm WLPs

    Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.

    标签: Considerations Guidelines and Design

    上传时间: 2013-10-14

    上传用户:ysystc699

  • PADS-PowerLogic and PowerPcb实用教程

    PADS-PowerLogic and PowerPcb实用教程

    标签: PADS-PowerLogic PowerPcb and 实用教程

    上传时间: 2014-12-24

    上传用户:youmo81