The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上传时间： 2014-01-17
上传用户：Altman
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
上传时间： 2013-12-08
上传用户：liansi
In this paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level simulation mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this paper, however,here we try to cover a few of them.
标签： Efficient Verilog Digital Coding
上传时间： 2013-11-23
上传用户：我干你啊
This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported device.
标签： demonstrates example on-chip EEPROM
上传时间： 2015-05-04
上传用户：wl9454
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： KEIL_IODemo allocation routines project
上传时间： 2013-12-08
上传用户：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： Allocation GNU_IODemo Example project
上传时间： 2015-05-04
上传用户：Amygdala
ITU-T Recommendation V.90 98年9月版本 A DIGITAL MODEM AND ANALOGUE MODEM PAIR FOR USE ON THE PUBLIC SWITCHED TELEPHONE NETWORK (PSTN) AT DATA SIGNALLING RATES OF UP TO 56 000 bit/s DOWNSTREAM AND UP TO 33 600 bit/s UPSTREAM
标签： MODEM Recommendation ANALOGUE DIGITAL
上传时间： 2014-01-17
上传用户：hn891122
dvbsnoop is a DVB/MPEG stream analyzer program. The program can be used to sniff, monitor, debug, dump or view DVB/MPEG/DSM-CC/MHP stream information (digital television or data broadcasts) sent via satellite, cable or terrestrial.
标签： program dvbsnoop analyzer monitor
上传时间： 2013-12-14
上传用户：zhangyi99104144
DIGITAL IMAGERY is pervasive in our world today. Consequently, standards for the efficient representation and interchange of digital images are essential. To date, some of the most successful still image compression standards have resulted from the ongoing work of the Joint Photographic Experts Group (JPEG). This group operates under the auspices of Joint Technical Committee 1, Subcommittee 29, Working Group 1 (JTC 1/SC 29/WG 1), a collaborative effort between the International Organization for Standardization (ISO) and International Telecommunication Union Standardization Sector (ITUT). Both the JPEG [1–3] and JPEG-LS [4–6] standards were born from the work of the JPEG committee. For the last few years, the JPEG committee has been working towards the establishment of a new standard known as JPEG 2000 (i.e., ISO/IEC 15444). The fruits of these labors are now coming to bear, as JPEG-2000 Part 1 (i.e., ISO/IEC 15444-1 [7]) has recently been approved as a new international standard.
标签： Consequently efficient pervasive standards
上传时间： 2013-12-21
上传用户：源弋弋
