为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
以太网和CAN总线应用广泛，但由于其通信协议不同，两种总线器件间无法进行数据通信，因此，设计了基于CP2200与C8051F040的以太网总线与CAN总线接口转换电路，并给出部分相关硬件电路与软件设计分析。在保证数据完整和协议可靠的前提下，通过握手协议和简化的以太网协议，不仅实现了以太网数据与CAN数据的转发，同时还顺利的解决了以太网的高速性与CAN的低速率冲突，以及两者数据包之间的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上传时间： 2013-10-15
上传用户：Ants
单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
针对盘山路存在的转弯盲区，即在转弯时司机无法得知弯路对面是否有车辆通过，设计一种基于C8051F310的山路转弯预防警示系统。该系统利用一阶滤波算法检测山路转弯时是否有车辆通过。运用该算法可增强系统检测的实时性，提高检测机动车辆的灵敏度，同时大大减少环境温度对检测的干扰。试验表明该系统能够正确指示出在山路转弯时是否有车辆通过，目前该系统已安装在盘山路上，可大大减少事故的发生率。 Abstract: Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
上传时间： 2013-10-10
上传用户：归海惜雪
在汽车发动机起动时，若发动机起动后起动机不能及时断电，将会烧毁起动机或损坏飞轮齿环；若变速器不在空档位置起动，则起动机的瞬间动力将使汽车位移，还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器，通过检测汽车起动开关、变速箱档位、发动机转速，实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统，解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上传时间： 2013-10-15
上传用户：mikesering
为满足矿井安全生产要求，介绍了一种以AT89C51单片机为主控器，对环境空气的温度、有毒易燃气体的浓度等进行检测的监控系统。该系统配合外围电路能实现对上述环境指标的控制并存储相关数据与上位PC机通信。它采用硬件抗干扰和软件抗干扰技术，以确保整个系统工作的准确性。 Abstract: In order to meet the needs of mine produce safety，a kind of intellignet mine ambient monotoring and control system based on AT89C51 is introduced.This system can detect the temperature of ambient of mine，the density of poisonous inflammable gas,combined external circuit.With its function part， this system can change above-mentioned elements.
上传时间： 2013-11-10
上传用户：wendy15
为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
为深入了解基于UC3854A控制的PFC变换器中的动力学特性，研究系统参数变化对变换器中分岔现象的影响，在建立Boost PFC变换器双闭环数学模型的基础上，用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上，分析了系统参数变化对分岔点的影响，并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上传时间： 2013-10-17
上传用户：杜莹12345
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
