锂电池BMS管理技术是移动机器人的关键技术,本文设计了基于bq76PL455、STM32F103的锂电池管理系统,实现了电池组电压、电流、过压、过流等状态监测;系统配置均衡电路,电池充电过程中若出现电池单体电压不平衡现象,会触发均衡电路,进而提高电池的安全性,延长使用寿命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the monitoring of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上传时间： 2022-04-02
上传用户：
在全球气候变暖和石油资源短缺的形势下,推动新能源汽车的发展将成为汽车行业一种新的发展方向。在大力发展新能源电动汽车行业的同时还应兼顾电动汽车充电设施的发展,因此对电动汽车充电桩的设计与研究显得十分必要。对电动汽车直流充电桩的硬件系统进行设计,主要的硬件电路包括安全监测电路、总压采集电路、温湿度检测电路、语音电路。软件包括主要流程图和温湿度检测流程图。Under the situation of global warming and shortage of petroleum resources,promoting the development of new energy vehicles will become a new development direction for the automotive industry.While vigorously developing the new energy electric vehicle industry,we should also take into account the development of electric vehicle charging facilities.Therefore,the design and research of electric vehicle charging piles is very necessary.The hardware system of the electric vehicle DC charging pile is designed.The main hardware circuits include safety monitoring circuit,total voltage collecting circuit,temperature and humidity detecting circuit,voice circuit and CAN communication.The software includes a main flow chart and a temperature and humidity detection flow chart.
标签： 电动汽车
上传时间： 2022-04-03
上传用户：jason_vip1
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
本文设计了一种磁致伸缩位移传感器,介绍了该磁致伸缩位移传感器的测量原理,通过结构优化设计提高了仪器的性能,详述了硬件电路设计及实现方法,完成了软件设计,实现了高压充电、问询脉冲加载、时间测量及滤波等功能,并通过实验对其性能进行了验证。所研制的磁致伸缩位移传感器具有测量精度高、长期稳定性好等特点,满足了大量程、高精度、恶劣环境等测量的要求。A kind of sensor based on magnetostrictive principle is designed.The measuring principle of the magnetostrictive displacement sensor is introduced,the performance of the instrument is improved by the structural optimization design,and introduced the hardware circuit design and the realization method,completed the software design,realized the functions of the high voltage charging,inquiries pulse loading,time measurement and filtering,and its performance is verified through the experiment.The magnetostrictive displacement sensor has the characteristics of high measuring precision.The sensor meets the requirements of large range,high precision,poor environment and so on.
标签： 位移传感器
上传时间： 2022-04-06
上传用户：
介绍一种万能模拟信号输入采集电路,可以同时支持电压、电流、热电偶、热电阻等常见的工业类型信号,方便后级电路的测量。该研究成果通过不断优化和完善,已成功应用到了中控仪表的新产品中。The paper introduces a collection circuit of universal signal input. The circuit support voltage, current, thermocouple, thermal resistance and other common industrial type signal. The research results, which has been continuous optimized and improved, has been successfully applied to the new production of Zhejiang Supcon Instrument Co., Ltd.
标签： 采集电路
上传时间： 2022-04-21
上传用户：slq1234567890
为适应双向DC/DC功率变换的电流采样需求,一种高精度高边电流采样电路被提出。其基本思想是在功率电路的高边串入采样电阻,借助电流镜原理并引入偏置电流电路,将双向电流均转换为正向电压输出。通过理论分析与仿真结合的方法对电流镜采样原理及4种不同的偏置电流电路方案进行对比,最后通过实验数据验证了高精度高边电流采样电路的有效性。实验数据表明,该采样电路可在-25~75℃的温度工作范围内,针对-10~＋10 A范围内的电流采样实现优于5%的采样精度。Current sensing plays an important role in controlling,monitoring or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...
上传时间： 2022-04-22
上传用户：
该步进电机驱动器又称为EasyDriver，EasyDriver能够为两级步进电机提供大约每相750mA（两极一共1.5A）的驱动。它默认设置为8步细分模式（所以如果你的电机是每圈200步，你使用EasyDriver时默认为每圈1600步），更多细分模式可以通过将MS1或MS2两个接脚接地进行设置。这是一种基于Allegro A3967驱动芯片的细分断路器。对于此设计的完整规格，请查阅A3967的参数表。它的最大每相电流从150mA到750mA。可以采用的最大驱动电压大概是30V，其中包括板载5V的调压器，所以只需要一个电源。质优价廉，这玩意儿只要十几美元，比你自己制作电路板更便宜。步进电机驱动器设计特色：· A3967 Microstepping Driver· MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)· Compatible with 4, 6, and 8 wire stepper motors of any voltage· Adjustable current control from 150mA/phase to 700mA/phase· Power supply range from 6V to 30V. The higher the voltage, the higher the torque at high speeds
上传时间： 2022-04-27
上传用户：
基于PSIM仿真软件，分析了Boost电路拓扑结构，设定了参数要求进行电路仿真设计，通过电路仿真软件PSIM对Boost电路工作在CCM模式下，合理设置占空比参数。实验结果表明理论分析与仿真的一致性和参数设计的正确性，输出电压和电流参数稳定，Boost电路输出效率高。This design is based on PSIM simulation software,analyzes the topology of Boost circuit,sets the parameter re- quirements for circuit simulation design,and reasonably sets the duty cycle parameters for Boost circuit working in CCM mode through PSIM simulation software.The experimental results show that the theoretical analysis and simulation are consis- tent and the parameter design is correct,the output voltage and current parameters are stable.
上传时间： 2022-05-04
上传用户：
The JW® 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of output current and offers low-power operation in miniaturized packaging. JW7805 supports fixed output voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low output noise and high PSRR are also friendly to RF systems.
标签： JW7805
上传时间： 2022-05-06
上传用户：slq1234567890
基于DSP28035的高速永磁无刷直流电机驱动系统，包括论文和软硬设计资料。摘要参赛作品为基于DSP28035的高速永磁无刷直流电机驱动系统。该系统以一台额定转速60 krpm的高速永磁无刷直流电机、交错并联的Buck电路以及全桥电路为硬件平台，以DSP28035为控制核心，实现了调压调速功能和基于坐标变换的无位置传感器新技术。为实现该系统要求，本作品充分利用了DSP28035的资源例如：CLA模块，模拟比较器、HPWM模块以及AD转换模块等。AbstractThis work is the drive system for a high speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s speed with voltage and the function of sensorless control based on the coordinate transformation. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁无刷直流电机驱动系统由于基波频率较高（一般在1kHZ以上），利用逆变桥斩波进行调速的控制方式通常会受到开关管开关频率的限制，因此该系统多采用三相全桥前级加Buck电路进承担调压调速的功能，而三相全桥主要承担逻辑换相的功能。然而，传统Buck电路所需电感的体积较大，增加了系统的体积，降低了系统的功率密度。
上传时间： 2022-05-08
上传用户：bluedrops
