This application note describes how to decode StANDard DTMF tones using the minimum number of external discrete components and a PIC. The two examples use a PIC which has an 8 bit timer and either a comparator or an ADC, although it can be modified for use on a PIC which has only digital I/O. The Appendices have example code for the 16C662 (with comparator) and 16F877 (using the ADC). As the majority of the Digital Signal Processing is done in software, little is required in the way of external signal conditioning. Software techniques are used to model the individual elements of a DTMF Decoder IC.
上传时间： 2013-11-21
上传用户：zhaoke2005
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international StANDard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上传时间： 2013-11-24
上传用户：Alick
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with StANDard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance when the PCA9519 is unpowered.
标签： 4channel transla level 9519
上传时间： 2013-11-19
上传用户：jisiwole
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with StANDard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
本文依据集成电路设计方法学，探讨了一种基于标准Intel 8086 微处理器的单芯片计算机平台的架构。研究了其与SDRAM，8255 并行接口等外围IP 的集成，并在对AMBA协议和8086 CPU分析的基础上，采用遵从AMBA传输协议的系统总线代替传统的8086 CPU三总线结构，搭建了基于8086 IP 软核的单芯片计算机系统，并实现了FPGA 功能演示。关键词：微处理器； SoC；单芯片计算机；AMBA 协议 Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the StANDard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the StANDard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
上传时间： 2013-12-27
上传用户：kernor
多功能高集成外围器件6. 1 多功能高集成外围器件82371PCI的英文名称：Peripheral Component Interconnect （外围部件互联PCI总线）；82371是PCI总线组件。ISA是：Industry StANDard Architecture（工业标准体系结构）IDE是 （Integrated Device Electronics）集成电路设备简称PIIX4PIIX4器件（芯片）的特点1、是一种支持Pentium和PentiumII微处理器的部件。2、82371对ISA桥来说，是一种多功能PCI总线。3、对可移动性和桌面深绿色环境均提供支持。4、电源管理逻辑。5、被集成化的IDE控制器。6、增强了性能的DMA控制器。 （7）基于两个82C59的中断控制器。（8）基于82C54芯片的定时器。（9）USB（Universal Serial Bus）通用串行总线。（10）SMBus系统管理总线。（11）实时时钟（12）顺应Microsoft Win95所需的功能其芯片的逻辑框图如图6-1所示。 PIIX4芯片逻辑框图6.1.1 概述PIIX4芯片是一个多功能的PCI器件，图6-2 是82371在系统中扮演的角色。（续上图）1. PCI与EIO之间的桥（PIIX4芯片）桥是不对程的，是各类不同标准总线与PCI总线连接，82371AB桥也可理解为一种总线转换译码器和控制器，桥内包含复杂的协议总线信号和缓冲器。(1).在PCI系统内，当PIIX4操作时，它总是作为系统内各种模块的主控设备，如USB和DMA控制器、IDE总线和分布式DMA的主控设备等，而且总是以ISA主控设备的名义出现。(2). 在向ISA总线或IDE总线进行传送操作的传送周期期间作为从属设备使用，并对内部寄存器译码。PIIX4芯片（桥）的配置(1).可以把PIIX4芯片配置成整个ISA总线，或ISA总线的子集，也可扩展成EIO总线。在使用EIO总线时，可以把未使用的信号配置成通用的输入和输出。(2).PIIX4可直接驱动5个ISA插槽；(3).能提供字节-交换逻辑、I/O的恢复支持、等待状态的生成以及SYSCLK的生成。(4).提供X-BUS键盘控制器芯片、BIOS芯片、实时时钟芯片、二级微程序器等的选择。2. IDE接口（总线主控设备的权利和同步DMA方式）IDE接口为4个IDE的设备提供支持，比如IDE接口的硬盘和CD-ROM等。注意：目前硬盘接口有5类：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口几乎在PC机最多，因为便宜。SCSI多用于服务器和集群机。IDE的PIO IDE速率：14MB/s；而总线主控设备IDE的速率：33MB/s在PIIX4芯片的IDE系统内，配有两个各次独立的IDE信号通道。3. 具有兼容性的模块—DMA、定时器/计数器、中断控制器等（1）在PIIX4内的两各82C37 DMA控制器经逻辑的组合，产生7个独立的可编程通道。通道[0：3]是通过与8个二进位的硬件连线实现的。通过以字节为单位的计数进行传送。而通道[5：7]是通过16个二进位的连线实现的，以字为单位的计数进行传送。（2）DMA控制器还能通过PCI总线，处理旧的DMA的两个不同的方法提供支持。（3）计数/定时器模块在功能上与82C54等价。（4）中断控制器与ISA兼容，其功能是两个82C59的功能之和。
上传时间： 2013-11-19
上传用户：3到15
The Infineon TriCore provides an Interrupt System with a high safety StANDard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps
上传时间： 2013-11-05
上传用户：uuuuuuu
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothStANDard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to StANDardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上传时间： 2013-10-21
上传用户：xiaozhiqban
winCE msdn讲座 XP Embedded Now and the future Windows XP Embedded Developmentand Deployment Model OverviewWindows XP Embedded Component ModelWindows XP Embedded Studio Tools Microsoft WindowsXP Embedded Product Highlights Componentized version of Windows XP Professional~ 12,000 components and updates as of Service Pack 2Flexible localizationSame binaries and API as Windows XP ProfessionalHotfixes and service packsEmbedded Enabling FeaturesRuns on StANDard PC hardwareSupports boot on hard drives, compact flash, DiskOnChipand read-only mediaSupport for remote install and remote bootHeadless device and remote management supportIntegration with Microsoft management tools
上传时间： 2013-10-31
上传用户：jrsoft
