The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both RX and Tx Interrupt Service Routines.
标签： ESAcademy following directory examples
上传时间： 2015-04-25
上传用户：hasan2015
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both RX and Tx Interrupt Service Routines.
标签： ESAcademy following directory examples
上传时间： 2013-12-13
上传用户：牛津鞋
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both RX and Tx Interrupt Service Routines.
标签： ESAcademy following directory examples
上传时间： 2014-01-06
上传用户：zukfu
A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX coupling,reflection of the environment, AWGN noise,DC offset,I/Q mismatch,etc.Performance of the whole system can be evaluated by changing the coding method,parameters of building blocks,and operation distance.Finally,some simulation results are presented in this paper.
标签： environment constructed simulation Simulink
上传时间： 2014-01-09
上传用户：zhangliming420
smsc911x 网卡驱动 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * RX Performance Tuning * Tested Platforms * RX Code Path * Tx Code Path * Platform Interface Descriptions
标签： 911x programmers 911 following
上传时间： 2014-12-02
上传用户：sssl
基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at RX. Comparing the difference in tx/RX signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
标签： simulator i.e. system-level link-level
上传时间： 2016-03-15
上传用户：xsnjzljj
在c++builder环境下一个串口通信程序，包括界面的设计和串口通信函数的设计，实现了串口通信。在文件夹TX-RX中。
上传时间： 2013-12-10
上传用户：ippler8
NRF905驱动代码 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable
标签： initialize 905 content Normal
上传时间： 2013-12-16
上传用户：lanjisu111
一个UWB仿真程序包，里面包含信号生成，信道模拟，Tx/RX等模块。M-file
上传时间： 2016-05-22
上传用户：xiaoxiang
(1) 315、433、868、915Mh的ISM 和SRD频段 (2) 最高工作速率500kbps，支持2-FSK、GFSK和MSK调制方式 (3) 高灵敏度（1.2kbps下-110dDm，1％数据包误码率） (4) 内置硬件CRC 检错和点对多点通信地址控制 (5) 较低的电流消耗（RX中，15.6mA，2.4kbps,433MHz） (6) 可编程控制的输出功率，对所有的支持频率可达+10dBm (7) 支持低功率电磁波激活功能 (8) 支持传输前自动清理信道访问（CCA），即载波侦听系统 (9) 快速频率变动合成器带来的合适的频率跳跃系统 (10) 模块可软件设地址，软件编程非常方便 (11) 标准DIP间距接口，便于嵌入式应用 (12) 单独的64字节RX和TX数据FIFO
上传时间： 2016-06-21
上传用户：anng
