The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, Or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register. Two interrupt inputs, INT0 and INT1, one fOr each of theSCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as anAND of the two interrupt inputs, is provided.
上传时间： 2013-12-07
上传用户：europa_lin
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel Or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPOrt A to POrt B, Or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two pOrts, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The PCA9546A is a quad bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, Or channels. Any individualSCx/SDx channel Or combination of channels can be selected, determined by thecontents of the programmable control register.
上传时间： 2013-11-16
上传用户：cc1915
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion fOr I2C-bus/SMBus applications and was developed toenhance the NXP SemiconductOrs family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed fOr ACPI power switches, sensOrs, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input Or Output selection); Input, Outputand Polarity Inversion (active HIGH Or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs Or outputs by writing to the I/O configurationbits. The data fOr each Input Or Output is kept in the cOrresponding Input Or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, Or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, Or channels. Any individualSCx/SDx channel Or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion fOr SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input pOrt register, 8-bit output pOrt register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input Or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library Or through direct writes to the device's control registers, this application note describesboth methods. The infOrmation presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
标签： Microcontr Stellaris Using the
上传时间： 2013-10-14
上传用户：blans
The main oscillatOr allows either a crystal Or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillatOr circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillatOr to clock the device after theboot process has completed.
标签： Stellaris Clocking Options fOr
上传时间： 2013-10-14
上传用户：pol123
The ISO7220 and ISO7221 are dual-channel digital isolatOrs. To facilitate PCB layout, the channels are Orientedin the same direction in the ISO7220 and in opposite directions in the ISO7221. These devices have a logic inputand output buffer separated by TI’s silicon-dioxide (SiO2) isolation barrier, providing galvanic isolation of up to4000 V. Used in conjunction with isolated power supplies, these devices block high voltage, isolate grounds, andprevent noise currents on a data bus Or other circuits from entering the local ground and interfering with Ordamaging sensitive circuitry.
上传时间： 2013-10-24
上传用户：hbsunhui
