The PAM2862 is a continuous mode inductivestep-down converter, designed for driving singleor multiple series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
上传时间： 2013-11-16
上传用户：司令部正军级
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
为了扩大监控范围，提高资源利用率，降低系统成本，提出了一种多通道视频切换的解决方案。首先从视频信号分离出行场信号，然后根据行场信号由DSP和FPGA产生控制信号，控制多路视频通道之间的切换，从而实现让一个视频处理器同时监控不同场景。实验结果表明，该方案可以在视频监控告警系统中稳定、可靠地实现视频通道的切换。 Abstract: To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and field sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. Experimental results show that the method can realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
上传时间： 2013-11-09
上传用户：不懂夜的黑
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上传时间： 2013-11-14
上传用户：fdmpy
很多不同的厂家生产各种型号的计算机，它们运行完全不同的操作系统，但TCP.IP协议族允许它们互相进行通信。这一点很让人感到吃惊，因为它的作用已远远超出了起初的设想。T C P / I P起源于6 0年代末美国政府资助的一个分组交换网络研究项目，到9 0年代已发展成为计算机之间最常应用的组网形式。它是一个真正的开放系统，因为协议族的定义及其多种实现可以不用花钱或花很少的钱就可以公开地得到。它成为被称作“全球互联网”或“因特网(Internet)”的基础，该广域网（WA N）已包含超过1 0 0万台遍布世界各地的计算机。本章主要对T C P / I P协议族进行概述，其目的是为本书其余章节提供充分的背景知识。 TCP.IP协议 缩略语 ACK (ACKnowledgment) TCP首部中的确认标志 API (Application Programming Interface) 应用编程接口 ARP (Address Resolution Protocol) 地址解析协议 ARPANET(Defense Advanced Research Project Agency NETwork) (美国)国防部远景研究规划局 AS (Autonomous System) 自治系统 ASCII (American Standard Code for Information Interchange) 美国信息交换标准码 ASN.1 (Abstract Syntax Notation One) 抽象语法记法1 BER (Basic Encoding Rule) 基本编码规则 BGP (Border Gateway Protocol) 边界网关协议 BIND (Berkeley Internet Name Domain) 伯克利I n t e r n e t域名 BOOTP (BOOTstrap Protocol) 引导程序协议 BPF (BSD Packet Filter) BSD 分组过滤器 CIDR (Classless InterDomain Routing) 无类型域间选路 CIX (Commercial Internet Exchange) 商业互联网交换 CLNP (ConnectionLess Network Protocol) 无连接网络协议 CRC (Cyclic Redundancy Check) 循环冗余检验 CSLIP (Compressed SLIP) 压缩的S L I P CSMA (Carrier Sense Multiple Access) 载波侦听多路存取 DCE (Data Circuit-terminating Equipment) 数据电路端接设备 DDN (Defense Data Network) 国防数据网 DF (Don’t Fragment) IP首部中的不分片标志 DHCP (Dynamic Host Configuration Protocol) 动态主机配置协议 DLPI (Data Link Provider Interface) 数据链路提供者接口 DNS (Domain Name System) 域名系统 DSAP (Destination Service Access Point) 目的服务访问点 DSLAM (DSL Access Multiplexer) 数字用户线接入复用器 DSSS (Direct Sequence Spread Spectrum) 直接序列扩频 DTS (Distributed Time Service) 分布式时间服务 DVMRP (Distance Vector Multicast Routing Protocol) 距离向量多播选路协议 EBONE (European IP BackbONE) 欧洲I P主干网 EOL (End of Option List) 选项清单结束 EGP (External Gateway Protocol) 外部网关协议 EIA (Electronic Industries Association) 美国电子工业协会 FCS (Frame Check Sequence) 帧检验序列 FDDI (Fiber Distributed Data Interface) 光纤分布式数据接口 FIFO (First In, First Out) 先进先出 FIN (FINish) TCP首部中的结束标志 FQDN (Full Qualified Domain Name) 完全合格的域名 FTP (File Transfer Protocol) 文件传送协议 HDLC (High-level Data Link Control) 高级数据链路控制 HELLO 选路协议 IAB (Internet Architecture Board) Internet体系结构委员会 IANA (Internet Assigned Numbers Authority) Internet号分配机构 ICMP (Internet Control Message Protocol) Internet控制报文协议 IDRP (InterDomain Routing Protocol) 域间选路协议 IEEE (Institute of Electrical and Electronics Engineering) （美国）电气与电子工程师协会 IEN (Internet Experiment Notes) 互联网试验注释 IESG (Internet Engineering Steering Group) Internet工程指导小组 IETF (Internet Engineering Task Force) Internet工程专门小组 IGMP (Internet Group Management Protocol) Internet组管理协议 IGP (Interior Gateway Protocol) 内部网关协议 IMAP (Internet Message Access Protocol) Internet报文存取协议 IP (Internet Protocol) 网际协议 I RTF (Internet Research Task Force) Internet研究专门小组 IS-IS (Intermediate System to Intermediate System Protocol) 中间系统到中间系统协议 ISN (Initial Sequence Number) 初始序号 ISO (International Organization for Standardization) 国际标准化组织 ISOC (Internet SOCiety) Internet协会 LAN (Local Area Network) 局域网 LBX (Low Bandwidth X) 低带宽X LCP (Link Control Protocol) 链路控制协议 LFN (Long Fat Net) 长肥网络 LIFO (Last In, First Out) 后进先出 LLC (Logical Link Control) 逻辑链路控制 LSRR (Loose Source and Record Route) 宽松的源站及记录路由 MBONE (Multicast Backbone On the InterNEt) Internet上的多播主干网 MIB (Management Information Base) 管理信息库 MILNET (MILitary NETwork) 军用网 MIME (Multipurpose Internet Mail Extensions) 通用I n t e r n e t邮件扩充 MSL (Maximum Segment Lifetime) 报文段最大生存时间 MSS (Maximum Segment Size) 最大报文段长度 M TA (Message Transfer Agent) 报文传送代理 MTU (Maximum Transmission Unit) 最大传输单元 NCP (Network Control Protocol) 网络控制协议 NFS (Network File System) 网络文件系统 NIC (Network Information Center) 网络信息中心 NIT (Network Interface Tap) 网络接口栓（S u n公司的一个程序） NNTP (Network News Transfer Protocol) 网络新闻传送协议 NOAO (National Optical Astronomy Observatories) 国家光学天文台 NOP (No Operation) 无操作 NSFNET (National Science Foundation NETwork) 国家科学基金网络 NSI (NASA Science Internet) （美国）国家宇航局I n t e r n e t NTP (Network Time Protocol) 网络时间协议 NVT (Network Virtual Terminal) 网络虚拟终端 OSF (Open Software Foudation) 开放软件基金 OSI (Open Systems Interconnection) 开放系统互连 OSPF (Open Shortest Path First) 开放最短通路优先 PAWS (Protection Against Wrapped Sequence number) 防止回绕的序号 PDU (Protocol Data Unit) 协议数据单元 POSIX (Portable Operating System Interface) 可移植操作系统接口 PPP (Point-to-Point Protocol) 点对点协议 PSH (PuSH) TCP首部中的急迫标志 RARP (Reverse Address Resolution Protocol) 逆地址解析协议 RFC (Request For Comments) Internet的文档，其中的少部分成为标准文档 RIP (Routing Information Protocol) 路由信息协议 RPC (Remote Procedure Call) 远程过程调用 RR (Resource Record) 资源记录 RST (ReSeT) TCP首部中的复位标志 RTO (Retransmission Time Out) 重传超时 RTT (Round-Trip Time) 往返时间 SACK (Selective ACKnowledgment) 有选择的确认 SLIP (Serial Line Internet Protocol) 串行线路I n t e r n e t协议 SMI (Structure of Management Information) 管理信息结构 SMTP (Simple Mail Transfer Protocol) 简单邮件传送协议 SNMP (Simple Network Management Protocol) 简单网络管理协议 SSAP (Source Service Access Point) 源服务访问点 SSRR (Strict Source and Record Route) 严格的源站及记录路由 SWS (Silly Window Syndrome) 糊涂窗口综合症 SYN (SYNchronous) TCP首部中的同步序号标志 TCP (Transmission Control Protocol) 传输控制协议 TFTP (Trivial File Transfer Protocol) 简单文件传送协议 TLI (Transport Layer Interface) 运输层接口 TTL (Ti m e - To-Live) 生存时间或寿命 TUBA (TCP and UDP with Bigger Addresses) 具有更长地址的T C P和U D P Telnet 远程终端协议 UA (User Agent) 用户代理 UDP (User Datagram Protocol) 用户数据报协议 URG (URGent) TCP首部中的紧急指针标志 UTC (Coordinated Universal Time) 协调的统一时间 UUCP (Unix-to-Unix CoPy) Unix到U n i x的复制 WAN (Wide Area Network) 广域网 WWW (World Wide Web) 万维网 XDR (eXternal Data Representation) 外部数据表示 XID (transaction ID) 事务标识符 XTI (X/Open Transport Layer Interface) X/ O p e n运输层接口
上传时间： 2013-11-13
上传用户：tdyoung
在现代通信系统中，电话语音的频带被限制在300 Hz～4 kHz的范围内，带来了语音可懂度和自然度的降低。为了在不增加额外成本的前提下提高语音的可懂度和自然度，进行了电话语音频带扩展的研究。提出了一种改进的基于码本映射的语音带宽扩展算法：在码本映射的过程中，使用加权系数来得到映射码本。客观测试结果表明，用此算法得到的宽带语音的谱失真度比用一般的码本映射降低至少2%。主观测试结果表明，用此算法得到的宽带语音具有更好的可懂度和自然度。 Abstract: In modern communication systems， the bandwidth of telephone speech is limited from 300Hz to 4 kHz， which reduces the intelligibility and naturalness of speech. Telephone speech bandwidth extension is researched to get wideband speech and to improve its intelligibility and naturalness， without increasing extra costs. This paper put forward an improved algorithm of speech bandwidth extension based on codebook mapping. In the process of codebook mapping， weighted coefficients were used to get mapping codebook. Objective tests show that spectral distortion of wideband speech obtained by this algorithm reduces at least 2%， comparing to conditional codebook mapping. Subjective tests show that the wideband speech obtained by this algorithm has better intelligibility and naturalness.
上传时间： 2014-12-29
上传用户：15501536189
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
