Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上传时间： 2013-11-18
上传用户：ZJX5201314
The makers of handheld medical, industrial and consumerdevices use a wide variety of high resolution, small tomedium sized color TFT LCD displays. The power supplydesigners for these displays must contend with shrinkingboard area, tight schedules, and variations in displaytypes and feature requirements. The LTC®3524 simplifi esthe designer’s job by combining a versatile, easily programmed,TFT LCD bias supply and white LED backlightdriver in a low profi le 4mm × 4mm QFN package.
上传时间： 2013-10-26
上传用户：chens000
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上传时间： 2014-01-18
上传用户：wenyuoo
Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
上传时间： 2013-10-09
上传用户：hanhanj
An essential component of a noise-free audio device isa clean power supply, but few switching regulators canoperate at high efficiency while keeping the switchingfrequency out of the audio band. The LTC®3620 fills thisvoid. It is a high efficiency 15mA buck regulator with aprogrammable minimum switching frequency, making itpossible to virtually eliminate audible switching noise. Theinternal synchronous switches and low quiescent currentof this buck regulator provide the ability to maintain highefficiency, while its small footprint makes it ideal for tiny,low power audio applications.
上传时间： 2013-10-21
上传用户：非衣2016
Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上传时间： 2013-10-25
上传用户：brain kung
