虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

Knowledge-embedded

  • XAPP806 -决定DDR反馈时钟的最佳DCM相移

    This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.

    标签: XAPP 806 DDR DCM

    上传时间: 2013-10-15

    上传用户:euroford

  • xilinx Zynq-7000 EPP产品简介

    The Xilinx Zynq-7000 Extensible Processing Platform (EPP) redefines the possibilities for embedded systems, giving system and software architects and developers a flexible platform to launch their new solutions and traditional ASIC and ASSP users an alternative that aligns with today’s programmable imperative. The new class of product elegantly combines an industrystandard ARMprocessor-based system with Xilinx 28nm programmable logic—in a single device. The processor boots first, prior to configuration of the programmable logic. This, along with a streamlined workflow, saves time and effort and lets software developers and hardware designers start development simultaneously. 

    标签: xilinx Zynq 7000 EPP

    上传时间: 2013-11-01

    上传用户:dingdingcandy

  • 基于FPGA+DSP模式的智能相机设计

    针对嵌入式机器视觉系统向独立化、智能化发展的要求,介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析,对国内外的几款智能相机进行比较。综合技术发展现状,提出基于FPGA+DSP模式的硬件平台,并提出智能相机的发展方向。分析结果表明,该系统设计可以实现脱离PC运行,完成图像获取与分析,并作出相应输出。 Abstract:  This paper introduced an embedded vision system-intelligent camera ,which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture, component modules and image acquisition, transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad, the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design, the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.

    标签: FPGA DSP 模式 智能相机

    上传时间: 2013-10-24

    上传用户:bvdragon

  • SOC验证方法

    Prakash Rashinkar has over 15 years experience in system design and verificationof embedded systems for communication satellites, launch vehicles and spacecraftground systems, high-performance computing, switching, multimedia, and wirelessapplications. Prakash graduated with an MSEE from Regional Engineering College,Warangal, in India. He lead the team that was responsible for delivering themethodologies for SOC verification at Cadence Design Systems. Prakash is anactive member of the VSIA Functional Verification DWG. He is currently Architectin the Vertical Markets and Design Environments Group at Cadence.

    标签: SOC 验证方法

    上传时间: 2014-01-24

    上传用户:xinhaoshan2016

  • XAPP807-封装最小的三态以太网MAC处理引擎

    The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.

    标签: XAPP 807 MAC 封装

    上传时间: 2013-10-26

    上传用户:yuzsu

  • 基于以太网的虚拟示波器设计

    为提升虚拟仪器传输速率与实时性能,扩展监测范围,在VC的软件平台上设计了一种全功能虚拟示波器。与传统虚拟示波器相比,该系统采用嵌入式系统完成信号采集,采用工业以太网为传输介质,通过线性插值算法和多线程编程思想,实现波形显示、参数计算、频谱分析以及波形存储及回放功能。实验结果表明,该虚拟示波器可以实现20 kHz采样频率下的波形精确显示,达到预期的各项指标。 Abstract:  o enhance the transfer rate and real-time of virtual instrument performance, expand scope of monitoring, this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope, this system adopts the embedded system to complete the data acquisition, industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas, namely to achieve waveform display, parameter calculation, spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency, and achieve the desired targets.

    标签: 以太网 虚拟 波器设计

    上传时间: 2013-11-25

    上传用户:wbwyl

  • Windows_CE嵌入式系统

     嵌入式系统(Embedded System)是以应用为中心,以计算机技术为基础,并且软硬件是可裁剪的,适用于对功能、可靠性、成本、体积、功耗等有严格要求的专用计算机系统。嵌入式系统最典型的特点是与人们的日常生活紧密相关,任何一个普通人都可能拥有各类形形色色运用了嵌入式技术的电子产品,小到MP3、PDA等微型数字化设备,大到信息家电、智能电器、车载GIS。 虽然嵌入式系统是近几年才开始真正风靡起来的,但事实上嵌入式这个概念却很早就已经存在了,从上个世纪70年代单片机的出现到今天各种嵌入式微处理器、微控制器的广泛应用,嵌入式系统少说也有了近30年的历史。纵观嵌入式系统的发展历程,大致经历了以下四个阶段:

    标签: Windows_CE 嵌入式系统

    上传时间: 2014-12-29

    上传用户:wangzeng

  • 基于S3C2410和Linux的智能家居系统的设计

    提出一种基于S3C2410和Linux的智能家居系统的设计,该系统通过ARM9微处理器和各种传感器模块实现温湿度的采集显示和控制、入侵防盗检测、液化气泄露检测;通过GPRS通讯将烟雾、煤气、红外等传感器的异常报警信息以短信方式通知用户;结合嵌入式Web服务器和CGI技术,以及USB摄像头的使用,通过连接PC实现实时远程视频、传感器数据信息的监控;同时通过QT-embedded GUI编写的GUI程序,可以将室内各种传感器采集的各项参数,以图形化的方式显示到LCD触摸屏上,实现本地监控。通过测试,该系统运行稳定、可靠,便于实际应用,市场前景广阔。

    标签: S3C2410 Linux 智能家居系统

    上传时间: 2013-11-19

    上传用户:sqq

  • PICMG_COM_0_R2_0COMe规范--原文资料

    A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.

    标签: PICMG_COM COMe

    上传时间: 2013-11-05

    上传用户:Wwill

  • 嵌入式C语言译自《C for Embedded Systems》

    很好的资源

    标签: Embedded Systems for 嵌入式

    上传时间: 2013-12-28

    上传用户:yanyueshen