介绍一种以MSP430单片机为基础的智能频率测量系统，采用硬件逻辑与软件指令相结合的方式控制闸门，实现0 MHz~10 MHz范围内无档切换的等精度测量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上传时间： 2013-10-28
上传用户：dbs012280
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-11-17
上传用户：vodssv
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
标签： Pulsoximeter Single-Chip Des
上传时间： 2013-10-27
上传用户：黑漆漆
用户程序示例教程 The Blinky project is a simple program for the LPC2138using Keil MCB2130 Microcontroller Board. It blinks the LEDs at speed according to the Potentiometer setting and prints the current seting to the Serial Port 1.In addition it generates a sine wave with an adjustable frequency on the speaker of the board.
上传时间： 2014-12-27
上传用户：hongmo
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
上传时间： 2013-11-07
上传用户：xy@1314
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-10-10
上传用户：inwins
PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516, PCA9518,P82B96, P82B715Abstract - Philips Semiconductors family of Repeaters, Hubs and Expanders are detailed in this application notethat discusses device operation, maximum cable length and frequency calculations and typical applications.
上传时间： 2013-11-21
上传用户：wlcaption
Microchip ZigBee协议栈:ZigBee™ 是专为低速率传感器和控制网络设计的无线网络协议。有许多应用可从ZigBee 协议受益，其中可能的一些应用有：建筑自动化网络、住宅安防系统、工业控制网络、远程抄表以及PC 外设。与其他无线协议相比， ZigBee 无线协议提供了低复杂性、缩减的资源要求，最重要的是它提供了一组标准的规范。它还提供了三个工作频带，以及一些网络配置和可选的安全功能。如果您正在寻求现有的控制网络技术（例如RS-422、RS-485）或专有无线协议的替代方案， ZigBee 协议可能是您所需的解决方案。此应用笔记旨在帮助您在应用中采用ZigBee 协议。 可以使用在应用笔记中提供的Microchip ZigBee 协议栈快速地构建应用。为了说明该协议栈的用法，本文包含了两个有效的演示应用程序。可将这两个演示程序作为参考或者根据您的需求经过简单修改来采用它们。此应用笔记中提供的协议栈函数库实现了一个与物理层无关的应用程序接口。 因此，无需做重大修改就可以轻松地在射频（Radio Frequency，RF）收发器之间移植应用程序。在此文档末尾的“常见问题解答”中提供了有关Microchip 协议栈和用法的一些常见问题及其答案。
上传时间： 2013-10-08
上传用户：u789u789u789
基于变频调速的水平连铸机拉坯辊速度控制系统Frequency Inverter Based Drawing RollerS peedC ontrolSy stem ofHorizontal Continuous Casting MachineA 伟刘冲旅巴(南 华 大 学电气工程学院，衡阳421001)摘要拉坯辊速度控制是水平连铸工艺的关键技术之一，采用变频器实现水平连铸机拉坯辊速度程序控制，由信号发生装置给变频器提供程控信号。现场应用表明该控制系统速度响应快，控制精度高，满足了水平连铸生产的需要。关键词水平连铸拉坯辊速度程序控制变频器Absh'act Speedc ontorlof dr awingor leris on eo fth ek eyte chnologiesfo rho rizontalco ntinuousca stingm achine.Fo rth ispu rpose,fr equencyco nverterisad optedfo rdr awingor lersp eedp rogrammablec ontorlof ho rizontalco ntinuousca stingm achine,th ep rogrammableco ntorlsi gnalto fr equencyc onverteris provided场a signal generator. The results of application show that the response of system is rapid and the control accuracy is high enough to meet thedemand of production of horizontal continuous casting.Keywords Horizontalco ntinuousc asting Drawingor ler Speedp rogrammablec ontrol Ferquencyin verter 随着 现 代 化工业生产对钢材需求量的日益增加，连铸生产能力已经成为衡量一个国家冶金工业发展水平的重要指标之一。近十几年来，水平连铸由于具有投资少、铸坯直、见效快等多方面的优点，国内许多钢铁企业利用水平连铸机来浇铸特种合金钢，发挥了其独特的优势并取得了较好的经济效益〔1,2)0采用 水 平 连铸机浇铸特种合金钢时，由于拉坯机是水平连铸系统中的关键设备之一，拉坯机及其控制性能的好坏直接影响着连铸坯的质量，因此，连铸的拉坯技术便成为整个水平连铸技术的核心。由于钢的冶炼过程是在高温下进行的，钢水温度的变化又容易影响铸坯的质量和成材率，因此，如何能在高温环境下控制好与铸坯速度相关的参数(拉、推程量，中停时间和拉坯频率等)对于确保连铸作业的进一步高效化，延长系统的连续作业时间十分关键。因此，拉坯辊速度控制技术是连铸生产过程控制领域中的关键技术之- [31
上传时间： 2013-10-12
上传用户：gxy670166755
选择映射法（SLM）和概率类算法都可以降低OFDM （Orthogonal Frequency Division Multiplexing）系统的PAPR（Peak to Average Power Ratio），传统SLM算法自身较为复杂，但由于其优良的性能，弃之可惜。研究表明，SLM算法和限幅类算法在性能上具有一定的互补性。任何一个算法未必能达到抑制PAPR的理想效果，在深入研究了两个算法的基础上，将其优点联合起来，以达到降低OFDM系统PAPR的目的。最后对联合改进算法进行了分析与仿真，并验证了联合改进算法的有效性和可行性
上传时间： 2013-11-22
上传用户：xinhaoshan2016
