实时时钟是微机保护装置的重要部件，在讨论PCF8583结构与功能的基础上，提出采用dsPIC33F系列微处理器与串行I2C时钟PCF8583的接口设计方案，给出了相应的接口电路与软件流程。该设计方案结构简单，可靠性高，开发周期短，具有一定的实用与参考价值。所设计的微机保护装置已投入现场运行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
上传时间： 2013-11-18
上传用户：Thuan
针对盘山路存在的转弯盲区，即在转弯时司机无法得知弯路对面是否有车辆通过，设计一种基于C8051F310的山路转弯预防警示系统。该系统利用一阶滤波算法检测山路转弯时是否有车辆通过。运用该算法可增强系统检测的实时性，提高检测机动车辆的灵敏度，同时大大减少环境温度对检测的干扰。试验表明该系统能够正确指示出在山路转弯时是否有车辆通过，目前该系统已安装在盘山路上，可大大减少事故的发生率。 Abstract: Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
上传时间： 2013-10-10
上传用户：归海惜雪
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
气压是气象监测中的一个重要参数，提出了一种气压数据采集模块设计方案，该模块采用数字气压传感器MS5534B、MSP430单片机MSP430F2272和带实时时钟（RTC）64 KB铁电存储器。通过低功耗软件设计方法以微安级整体平均功耗实现了气压数据的采集和存储，适合电池供电的连续高精度气压采集应用。给出了模块的软硬件设计以及MS5534B的性能指标和使用经验。 Abstract: Air pressure is an important parameter in weather monitor.This paper futs forward a new design scheme of low power-air pressure data acquisition module.The module uses a digital output barometer sensor MS5534B,MSP430 microcontroller MSP430F2272 and integrated RTC 64KB FRAM,precision air pressure measurement and storage chip.Another point of this module is low power consumption, so it is well suited for battery powered air pressure data acquisition applications. At the same time,the software and hardware deign of module is presented,And the speciaties and use notices of MS5534B are given.
上传时间： 2014-12-27
上传用户：drink！
介绍一种以MSP430单片机为基础的智能频率测量系统，采用硬件逻辑与软件指令相结合的方式控制闸门，实现0 MHz~10 MHz范围内无档切换的等精度测量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上传时间： 2013-10-28
上传用户：dbs012280
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-09
上传用户：ligi201200
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上传时间： 2013-11-08
上传用户：laozhanshi111
为了在工业生产及过程控制中准确测量温度，设计了一种基于低功耗MSP430单片机的数字温度计。整个系统通过单片机MSP430F1121A控制DS18B20读取温度，采用数码管显示，温度传感器DS18B20与单片机之间通过串口进行数据传输。MSP430系列单片机具有超低功耗，且外围的整合性高，DS18B20只需一个端口即可实现数据通信，连接方便。通过多次实验证明，该系统的测试结果与实际环境温度一致，除了具有接口电路简单、测量精度高、误差小、可靠性高等特点外，其低成本、低功耗的特点使其拥有更广阔的应用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上传时间： 2013-10-16
上传用户：wettetw
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
NEC 16位MCU参考手册 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上传时间： 2013-11-02
上传用户：努力努力再努力
