All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
Presents short and simple I2C software routines that support onlyslave (rather than master or master & slave) operation and an ASMdemonstration program. The slave-only software in this app notecomplements the master mode software presented in AN464, Usingthe 87LPC76X microcontroller as an I2C bus master.
上传时间： 2013-11-22
上传用户：1039312764
中文版详情浏览：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
标签： UltraScale Xilinx 架构
上传时间： 2013-11-13
上传用户：瓦力瓦力hong
The introduction of Spartan-3™ devices has createdmultiple changes in the evolution of embedded controldesigns and pushed processing capabilities to the “almostfreestage.” With these new FPGAs falling under $20, involume, with over 1 million system gates, and under $5for 100K gate-level units, any design with programmablelogic has a readily available 8- or 16-bit processor costingless than 75 cents and 32-bit processor for less than $1.50.
上传时间： 2013-12-10
上传用户：zgu489
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
上传时间： 2013-10-08
上传用户：yjj631
针对飞行模拟器座舱数据采集的复杂性，设计了一种基于以太网分布式的数据采集控制系统，该系统是RCM5700微处理器模块上的以太网应用。在系统的基础上具体讨论了PoE技术的应用，在传输数据的网线上同时提供电流，提出并实现了一种包括辅助电源在内的完整可靠的PoE供电方案。设计采用美国国家半导体的LM5073和LM5576并根据不同的负载情况，进行稳定可靠的电压转换，以满足数据采集电路的要求。实验结果表明：该设计稳定可靠，满足低于13 W的采集节点供电要求，提高了模拟器信号采集系统的通用性和标准化程度，避免了以往数据采集节点单独繁琐的电源设计。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上传时间： 2013-11-09
上传用户：xyipie
The #1 Step-by-Step Guide to labviewNow Completely Updated for labview 8! Master labview 8 with the industry's friendliest, most intuitive tutorial: labview for Everyone, Third Edition. Top labview experts Jeffrey Travis and Jim Kring teach labview the easy way: through carefully explained, step-by-step examples that give you reusable code for your own projects! This brand-new Third Edition has been fully revamped and expanded to reflect new features and techniques introduced in labview 8. You'll find two new chapters, plus dozens of new topics, including Project Explorer, AutoTool, XML, event-driven programming, error handling, regular expressions, polymorphic VIs, timed structures, advanced reporting, and much more. Certified labview Developer (CLD) candidates will find callouts linking to key objectives on NI's newest exam, making this book a more valuable study tool than ever. Not just what to d why to do it! Use labview to build your own virtual workbench Master labview's foundations: wiring, creating, editing, and debugging VIs; using controls and indicators; working with data structures; and much more Learn the "art" and best practices of effective labview development NEW: Streamline development with labview Express VIs NEW: Acquire data with NI-DAQmx and the labview DAQmx VIs NEW: Discover design patterns for error handling, control structures, state machines, queued messaging, and more NEW: Create sophisticated user interfaces with tree and tab controls, drag and drop, subpanels, and more Whatever your application, whatever your role, whether you've used labview or not, labview for Everyone, Third Edition is the fastest, easiest way to get the results you're after!
上传时间： 2013-10-14
上传用户：shawvi
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
为了能够满足基站易于选址、优质快速的建站要求和易维护、低成本、高可靠的运行要求，本文对以方舱来实现一体化结构基站做出一番探讨。从系统设计的观点阐述了移动通信高性能基站天线设计的几个关键问题，介绍了智能天线技术在基站中的应用，并且用HFSS软件仿真了一种新型的对称阵子天线，该天线驻波比小于2的带宽可以达到60%，具有良好的宽频带特性。 Abstract: In order to meet the station construction requirement of easy site selection and fast base station， and meet the operational requirement of easy maintenance， low cost and high reliability， this paper discussed the unified architecture base station using shelter. Several key problems of high performance mobile communication base station antenna were illustrated from the view of system design， the application of smart antenna in base station was also introduced. And a novel dipole antenna was simulated by using HFSS， the VSWR of the antenna is less than 2， and the bandwidth was reach to 60%. So it has good broadband properties.
上传时间： 2013-11-20
上传用户：linlin
本软件是关于MAX338, MAX339的英文数据手册：MAX338, MAX339 8通道/双4通道、低泄漏、CMOS模拟多路复用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上传时间： 2013-11-12
上传用户：18711024007
