目前开关电源市场上单端反激式的开关电源占有很大的份额，控制环路的设计是反激电源中关键的步骤之一。主要对基于L6561临界（TM）模式下高功率因数（PF）单端反激式开关电源的控制环路设计进行了论述，文中通过对环路中各级的传递函数进行了定性分析和定量计算，进而给出了环路的补偿电路。通过选择合适的相位裕量来保证系统的稳定性，并通过图解法验证了该环路可以使系统具有较好的稳定性。
上传时间： 2013-10-14
上传用户：zukfu
利用太阳能、风能及市电交流电能互补的三能一体电源，以LED灯作为负载，构成一套长效、稳定的照明系统，用于广告用霓虹灯、风景区独特建筑装饰照明等场所，具有节能、经济、环保的社会和经济效益。
上传时间： 2013-12-20
上传用户：lvchengogo
当前的快速充电器不能遵循蓄电池自身的特性进行快速充电，致使析气多，温升大，缩短电池的使用寿命。针对上述问题，创新性地提出应用ANFIS对电池的可接受电流进行预测，保证电池在最佳充电速率下快速无损充电。详细介绍以单片机XC164CM为核心，完成新型快速无损智能充电器的设计，具有电流检测和控制等功能。样机测试表明，充电过程中析气少，温升低，充电效率高，解决了充电速率与电池寿命之间的矛盾。
标签： 智能充电器
上传时间： 2013-10-19
上传用户：guanhuihong
为了提高稀土超磁致伸缩换能器驱动电源的效率以及实用性，采用DSP器件TMS320F2812作为主控芯片，结合混合脉宽调制方法实现SPWM波形。采用半桥型逆变电路实现SPWM的功率放大，并对隔离驱动电路、反馈电路和滤波匹配电路进行合理而有效的设计，保证了换能器的输出效能。同时使用电流控制频率的方法实现谐振频率的自动跟踪。实验证明，该驱动电路输出频率稳定，波形失真度低，且能量转换效率较高。
上传时间： 2013-10-30
上传用户：yueguizhilin
Abstract: With its small size and large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.
上传时间： 2013-10-20
上传用户：2728460838
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
The core voltages for FPGAs are moving lower as a resultof advances in the fabrication process. The newest FPGAfamily from Altera, the Stratix® II, now requires a corevoltage of 1.2V and the Stratix, Stratix GX, HardCopy®Stratix and CycloneTM families require a core voltage of1.5V. This article discusses how to power the core and I/Oof low voltage FPGAs using the latest step-down switchmode controllers from Linear Technology Corporation.
上传时间： 2013-10-08
上传用户：wangfei22
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with high-side inductor current
上传时间： 2013-11-20
上传用户：stewart·
Many telecommunications and computing applicationsneed high effi ciency step-down DC/DC converters thatcan operate from a very low input voltage. The highoutput power synchronous controller LT3740 is idealfor these applications, converting input supplies rangingfrom 2.2V to 22V to outputs as low as 0.8V with loadcurrents from 2A to 20A. Applications include distributedpower systems, point-of-load regulation and conversionof logic supplies.
上传时间： 2013-11-05
上传用户：zhf01y
