万瑞和电子从事自恢复保险丝的研发及生产至今已有12年，十多年来，公司自主研发和生产“万和”牌“插件式自恢复保险丝”（PTC）、“贴片式自恢复保险丝”（SMD）、“负温度系数热敏电阻”（NTC）、“IC元器件”等多系列、多型号产品，且通过了GE、UL、TUV、CE、CQC等多项安规认证，并符合欧盟RoHS环保指令要求，已广泛应用于通讯、影音设备、电动玩具、电动工具、电源、灯具、计算机、汽车电子等领域，并已成功地进入国际市场。
上传时间： 2013-10-09
上传用户：taozhihua1314
短距离无线通信技术是目前新兴的通信网络技术，它的应用有效地克服了传统有线控制的弊端，使得系统更加智能化。此外，随着绿色照明与智能家居日益受到广泛关注，短距离无线通信技术也逐渐开始应用在相关领域。所以，针对于此，本文设计并完成了基于TI CC430 系列和UCC28810 的无线LED 照明系统，旨在提供一种新颖、高效以及智能化的无线LED 照明系统解决方案。
上传时间： 2013-11-08
上传用户：yyq123456789
RT7273是一颗完全跟TPS65251 PIN TO PIN 替换料号,一路进三路出,输出电流可以做到3A/2A/2A;如有需求请联系我：021-54262182 EXT 114(Eric) QQ：1187337351
上传时间： 2013-11-24
上传用户：fairy0212
计算机的ATX电源脱离主板是需要短接一下20芯接头上的绿色（power on）和黑色（地）才能启动的。启动后把万用表拨到主流电压20V档位，把黑表笔插入4芯D型插头的黑色接线孔中，用红表笔分别测量各个端子的电压。楼上列的是20芯接头的端子电压，4芯D型插头的电压是黄色＋12V，黑色地，红色＋5V。 主板电源接口 图解 20-PIN ATX主板电源接口
上传时间： 2013-10-28
上传用户：蒋清华嗯
LM2596开关电压调节器是降压型电源管理单片集成电路，能够输出3A的驱动电流，同时具有很好的线性和负载调节特性。固定输出版本有3.3V、5V、12V， 可调版本可以输出小于37V的各种电压。 该器件内部集成频率补偿和固定频率发生器，开关频率为150KHz，与低频开关调节器相比较，可以使用更小规格的滤波元件。由于该器件只需4个外接元件，可以使用通用的标准电感，这更优化了LM2596的使用，极大地简化了开关电源电路的设计。 其封装形式包括标准的5脚TO-220封装（DIP）和5脚TO-263表贴封装（SMD）。 该器件还有其他一些特点：在特定的输入电压和输出负载的条件下，输出电压的误差可以保证在±4%的范围内，振荡频率误差在±15%的范围内；可以用仅80μA的待机电流， 实现外部断电；具有自我保护电路（一个两级降频限流保护和一个在异常情况下断电的过温完全保护电路） ※ 3.3V、5V、12V的固定电压输出和可调电压输出 ※ 可调输出电压范围1.2V～37V±4% ※ 输出线性好且负载可调节 ※ 输出电流可高达3A ※ 输入电压可高达40V ※ 采用150KHz的内部振荡频率，属于第二代开关电压调节器，功耗小、效率高 ※ 低功耗待机模式，IQ的典型值为80μA ※ TTL断电能力 ※ 具有过热保护和限流保护功能 ※ 封装形式：TO-220（T）和TO-263（S） ※ 外围电路简单，仅需4个外接元件， 且使用容易购买的标准电感
上传时间： 2014-12-24
上传用户：ttpay
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
上传时间： 2013-10-09
上传用户：hanhanj
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
通过分析一起500 kV 输电线路地线掉线事故，认为其主要原因是线路设计及绝缘子缺陷产生过大感应电压，加速了绝缘子的老化导致掉线。针对目前输电线路设计、运行的不足和潜在安全隐患，提出防止地线掉线、改进防雷性能的对策，并结合实际对保护OPGW 光缆的课题进行了初步的探讨。
上传时间： 2013-10-18
上传用户：541657925
