苏泊尔C21S02-B电磁炉电路图,红线标注，重点模块说明！
上传时间： 2013-06-22
上传用户：huangzr5
制作基于PIC Mcu 的ADS-B接收机的全套资料，包括SCH、PCB、源码和PC端软件。
上传时间： 2013-04-24
上传用户：cx111111
2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.
上传时间： 2013-10-07
上传用户：ysystc670
PSHLY-B回路电阻测试仪介绍
上传时间： 2013-11-05
上传用户：木子叶1
1.1MCS51实验系统安装与启动1.DVCC系列实验系统在出厂时均为51状态对DVCC—52196JH机型：SK1位1—5置ON位置，位6—10置OFF对DVCC—5286JH和DVCC—598JH机型：a.SK1位1—5置ON，位6—10置OFF；b.SK2位1—2置ON；c.SK3置ON；d.SK4置OFFe.卧式KBB置51、96位置,立式KBB1开关置51、88位置（只对DVCC—598JH/JH+）；f.DL1—DL4连1、22.如果系统用于仿真外接用户系统，将40芯仿真电缆一头插入系统中J6插座，另一头插入用户系统的8051CPU位置，注意插入方向，仿真头上小红点表示第一脚，对应用户8051CPU第一脚。3.接上+5V电源，将随机配备的2芯电源线，红线接入外置电源的+5V插孔，黑线接入外置电源地插座。上电后，DVCC系列实验系统上显示“P.”闪动。如果是独立运行，按DVCC系列用户手册进入键盘管理监控，就能马上做实验。键盘管理监控操作详见第一分册第四章。如果连上位机工作，必须将随机配备的D型9芯插头一端插入DVCC系统J2插座，另一端插入上位机串行口COM1—COM2任选。然后按DVCC实验系统PCDBG键，再运行上位机上的DVCC联机软件，双方建立通信，往后详细操作见用户手册第五章。如果电源内置，只需打开～220V电源开关即可。
上传时间： 2013-10-12
上传用户：xc216
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
TKS仿真器B系列快速入门
上传时间： 2013-10-31
上传用户：aix008
一个简单好用的B+树算法实现
上传时间： 2015-01-04
上传用户：缥缈
一个用Basic实现的B-Tree算法
上传时间： 2013-12-30
上传用户：ccclll
一个用Java applet实现的B-Tree算法
上传时间： 2013-12-25
上传用户：qiao8960
