M.NT68676.2A is a monitor control board, which is suitable for Asia-Pacific market. It can supportLED/LCD panels which resolution is up to 2048×1152.M.NT68676.2A can synchronize with computer automatically. Synchronization requires thesynchronous signal which horizontal and vertical sync are separated.M.NT68676.2A can support dynamic contrast control, headphone input and Digital volume controlsimultaneously.
标签： 乐华驱动板
上传时间： 2022-03-13
上传用户：kent
电子书-RTL Design Style Guide for Verilog HDL540页A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
标签： RTL verilog hdl
上传时间： 2022-03-21
上传用户：canderile
本设计介绍了一种基于STM32单片机控制的智能水杯,可利用插口式电源或无线充电底座为加热器提供能量,并在达到某种饮品所需温度时进行保温。水杯内置充电电池,可选用USB接口或无线充电。在水杯内部设置无线模块,用户利用手机App与水杯进行匹配进行加热操作,加热完后水杯会通过手机App和液晶显示屏实时反馈液体温度,通过指示灯显示电量情况等,给用户进行提醒。该智能水杯设计创新,实用价值较高。This paper introduces an intelligent water cup based by STM32 microcontroller,it can provide energy for the heater by socket type power supply or wireless charging base,and hold temperature needed for some kind of drink.Builtedin rechargeable battery,water cup can use USB or wireless charging.The wireless module is set up inside it,and customers can use mobile App to match and heat.After heating,water cup feeds back liquid temperature through the mobile App,and then displays on LCD,reminds users through the indicator light.The intelligent water cup is designed innovatively and has high practical value.
上传时间： 2022-03-28
上传用户：
近距电能传输——高效安全近距电能传输一般基于电磁感应原理进行。在此技术基础上，当接收器邻近发射器时才会进行电能传输。电磁感应技术的历史长达百年，多年米一直应用于各类电子产品中—如此普及全因其简单、高效以及安全技术概览以下将为你简要介绍无线电能传输技术。System Overview(Communication)Receiver sends messagesTo provide control information to the transmitterBy load modulation on the power signaTransmitter receives messagesTo receive control information frorn the recelverBy de-modulation of the reflected loadPower Pick Up( Receiver)Secondary coil (L Serial resonance capacitor (C) for efficient power transfer Parallel resonance capacitor(C, )for detection purposes Rectifier: full bridge(diode, or switched)+ capacitor Output switch for(dis)connecting the loadReceiver modulates load by Switching modulation resistor(R,n),or Switching modulation capacitor(Ca)Transmitter de-modulates reflected load by Sensing pnmary coil curent (p)and/o Sensing primary coil voltage (V,
上传时间： 2022-03-31
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
针对目前MSP430单片机实验装置较少、实验内容少,而且无MSP430高端产品的实验装置,研制了基于MSP430F5529单片机的综合实验装置,主要包括MSP430 Launch Pad和母板两部分。较传统的单片机实验装置增加了模拟电路的设置,设计的实验能够利用单片机的所有外设,可进行模块基础实验和综合实验两大类实验,非常适合自动化和电气信息类大学生学习使用。Concerning with the lack of experimental equipment and content based on MSP430,and especially,the experimental equipment of MSP430 senior products,an experimental equipment based on MSP430F5529 microcontroller is developed. It mainly consists of two parts： MSP430 Launch Pad and main board. Compared with traditional microcontroller experiment equipment,a few analog circuits were added. The experiment we set up takes advantage of all microcontroller peripherals. Students can do two kinds of experiments： module experiment and complex experiment.Therefore it fits university students in automation and electrical major very well.
标签： msp430f5529 单片机
上传时间： 2022-04-13
上传用户：
意法半导体STM8系列参考手册Program memory: 8 Kbyte Flash memory; dataretention 20 years at 55 °C after 100 cycles• RAM: 1 Kbyte• Data memory: 128 bytes true data EEPROM;endurance up to 100 k write/erase cycles
标签： stm8
上传时间： 2022-04-27
上传用户：zhaiyawei
为解决移相全桥电路驱动及相角控制问题,设计了一种数字控制的移相全桥驱动电路.以TPL521为光耦隔离、IR2110为栅极驱动芯片.由DSP产生PWM信号,经过光耦隔离和逻辑电路后送至IR2110进行相角控制.文章对IR2110驱动电路原理进行分析及参数进行设计,对TMS320F28335进行设置并给出部分代码.实验结果表明：通过TMS320F28335可产生的不同相角的PWM波形,满足了移相全桥对不同相角控制的要求.In order to solve the problem of phase-shifted full-bridge circuit driving and phase angle control,a digitally controlled phaseshifted full-bridge driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted full-bridge control for different phase angles.
上传时间： 2022-05-03
上传用户：zhanglei193
The JW® 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of output current and offers low-power operation in miniaturized packaging. JW7805 supports fixed output voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low output noise and high PSRR are also friendly to RF systems.
标签： JW7805
上传时间： 2022-05-06
上传用户：slq1234567890
以STM32F103C8T6为核心,设计了无刷直流电机控制器硬件电路。电路主要包括IR2310构成的PWM驱动电路、IRF3808构成的逆变电路、增量式旋转编码构成的速度反馈电路。控制器具有CAN和RS232通信接口,可与计算机或PLC构成速度或位置伺服系统。利用由xPC目标搭建的半实物仿真平台对PI参数进行整定。测试了控制器的速度伺服响应性能,给定速度为2400rpm时,控制器响应时间为0.32s。实验结果表明,系统工作可靠,稳定性好,响应速度快,可以满足上肢康复机器人的机械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,inverter circuit formed by IRF3808,speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the speed is 2 400 rpm,the response time of the controller is 0...
上传时间： 2022-05-07
上传用户：
