The PW4556 series of devices are highly integrated Li-Ion and Li-Pol linear chargers targetedat small capacity battery for portable applications. It is a complete constant-current/ constantvoltage linear charger. No external sense resistor is needed, and no blocking diode is required dueto the internal MOSFET architecture. It can deliver up to 300mA of charge current (using a goodthermal PCB layout) with a final float voltage accuracy of ±1%. The charge voltage is fixed at 4.2V or4.35V, and the charge current can be programmed externally with a single resistor. The chargerfunction has high accuracy current and voltage regulation loops and charge termination
标签： pw4556
上传时间： 2022-02-11
上传用户：1208020161
The PW4554 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger.The charger uses a CC/CV charge profile required by Li-ion battery. The charger accepts an inputvoltage up to 24V but is disabled when the input voltage exceeds the OVP threshold, typically 6.8V,to prevent excessive power dissipation. The 24V rating eliminates the over-voltage protection circuitrequired in a low input voltage charger
标签： pw4554
上传时间： 2022-02-11
上传用户：
The PW3130 series product is a high integration solution for lithium-lion/polymer batteryprotection.PW3130 contains advanced power MOSFET, high-accuracy voltage detection circuits anddelay circuits. PW3130 is put into an ultra-small SOT23-5 package and only one external componentmakes it an ideal solution in limited space of battery pack. PW3130 has all the protection functionsrequired in the battery application including overcharging, overdischarging, overcurrent and loadshort circuiting protection etc. The accurate overcharging detection voltage ensures safe and fullutilization charging.The low standby current drains little current from the cell while in storage. Thedevice is not only targeted for digital cellular phones, but also for any other Li-Ion and Li-Polybattery-powered information appliances requiring long-term battery life
标签： pw3130
上传时间： 2022-02-11
上传用户：fliang
The PW2606B is a front-end over voltage and over current protection device. It achieves wide inputvoltage range from 2.5VDC to 40VDC. The over voltage threshold can be programmed externally orset to internal default setting. The low resistance of integrated power path nFET switch ensures betterperformance for battery charging system applications. It can deliver up to 1A current to satisfy thebattery supply system. It integrates the over-temperature protection shutdown and auto-recoverycircuit with hysteresis to protect against over current events
标签： pw2606b
上传时间： 2022-02-11
上传用户：
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
标签： pw2601
上传时间： 2022-02-11
上传用户：
The PW2228A is a high efficiency single inductor Buck-Boost converter which can supply theload current up to 1.5A. It provides auto-transition between Buck and Boost Mode. The PW2228Aoperates at 2.4MHz switching frequency in CCM. DC/DC converter operates at Pulse-Skipping Modeat light load. The output voltage is programmable using an external resistor divider, or is fixed to3.3V internally. The load is disconnected from the VIN during shutdown.The PW2228A is available in TDFN3X3-10 package.
标签： pw2228a
上传时间： 2022-02-11
上传用户：
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
标签： pw2053
上传时间： 2022-02-14
上传用户：jason_vip1
PW1555 is a programmable current limit switch with input voltage range selection and outputvoltage clamping. Extremely low RDS(ON) of the integrated protection N-channel FET helps toreduce power loss during the normal operation. Programmable soft-start time controls the slew rateof the output voltage during the start-up time. Independent enable control allows the complicatedsystem sequencing control. It integrates the over-temperature protection shutdown andautorecovery with hystersis
标签： pw1555
上传时间： 2022-02-14
上传用户：
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
某客户工程师在某型号新产品的设计中，使用了CR95HF。工程师无法找到关于CR95HF上电初始化的具体步骤说明。结论：CR95HF上电后进入Power up状态，如果此时MCU无法与CR95HF通信或CR95HF的外部晶体没有起振，那么原因就在于MCU没有给CR95HF提供一个IRQ_In。
标签： cr95hf
上传时间： 2022-02-22
上传用户：
