完整性高的FPGA-PCB系统化协同设计工具 Cadence OrCAD and Allegro FPGA System Planner便可满足较复杂的设计及在设计初级产生最佳的I/O引脚规划，并可透过FSP做系统化的设计规划，同时整合logic、schematic、PCB同步规划单个或多个FPGA pin的最佳化及layout placement，借由整合式的界面以减少重复在design及PCB Layout的测试及修正的过程及沟通时间，甚至透过最佳化的pin mapping、placement后可节省更多的走线空间或叠构。 Specifying Design Intent 在FSP整合工具内可直接由零件库选取要摆放的零件，而这些零件可直接使用PCB内的包装，预先让我们同步规划FPGA设计及在PCB的placement。
标签： Allegro Planner System FPGA
上传时间： 2013-11-06
上传用户：wwwe
本软件是关于MAX338, MAX339的英文数据手册：MAX338, MAX339 8通道/双4通道、低泄漏、CMOS模拟多路复用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上传时间： 2013-11-12
上传用户：18711024007
本书是模拟集成电路设计课的一本经典教材。全书共分5个部分。主要介绍了模拟集成电路设计的背景知识、基本MOS半导体制造工艺、CMOS技术、CMOS器件建模，MOS开关、MOS二极管、有源电阻、电流阱和电流源等模拟CMOS分支电路，以及反相器、差分放大器、共源共栅放大器、电流放大器、输出放大器等CMOS放大器的原理、特性、分析方法和设计，CM0S运算放大器、高性能CMOS运算放大器、比较器，开关电容电路、D／A和A／D变换器等CMOS模拟系统的分析方法、设计和模拟等内容。
上传时间： 2013-10-30
上传用户：笨小孩
This example provides a description of how to use the USART with hardware flowcontrol and communicate with the Hyperterminal.First, the USART2 sends the TxBuffer to the hyperterminal and still waiting fora string from the hyperterminal that you must enter which must end by '\r'character (keypad ENTER button). Each byte received is retransmitted to theHyperterminal. The string that you have entered is stored in the RxBuffer array. The receivebuffer have a RxBufferSize bytes as maximum. The USART2 is configured as follow: - BaudRate = 115200 baud - Word Length = 8 Bits - One Stop Bit - No parity - Hardware flow control enabled (RTS and CTS signals) - Receive and transmit enabled - USART Clock disabled - USART CPOL: Clock is active low - USART CPHA: Data is captured on the second edge - USART LastBit: The clock pulse of the last data bit is not output to the SCLK pin
上传时间： 2013-10-31
上传用户：yy_cn
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
superpro 3000u 驱动 PIC16C65B@QFP44 [SA245] PIC16C65B: Part number QFP44: Package in QFP44 SA245: Adapter purchase number AM29DL320GT@FBGA48 [SA642+B026] AM29DL320GT: Part number FBGA48: Package in FBGA48 SA642: Adapter purchase number (Top board with socket) B026: Adapter purchase number (Bottom board, exchangable for different parts) 87C196CA@PLCC68(universal adapter) [PEP+S414T] 87C196CA: Part number PLCC68: Package in PLCC68 universal adapter: this adapter is valid for all parts in this package PEP: The PEP (Pin-driver Expansion Pack necessary to work with the adapter S414T) S414T: Adapter purchase number (Universal for all parts in this package) S71PL127J80B@FBGA64(special adapter) [(SA642A-B079A-Y096AF001)] S71PL127J80B: Part number FBGA64: Package in FBGA64 special adapter: this adapter is valid for this
上传时间： 2013-10-23
上传用户：Avoid98
完整性高的FPGA-PCB系统化协同设计工具 Cadence OrCAD and Allegro FPGA System Planner便可满足较复杂的设计及在设计初级产生最佳的I/O引脚规划，并可透过FSP做系统化的设计规划，同时整合logic、schematic、PCB同步规划单个或多个FPGA pin的最佳化及layout placement，借由整合式的界面以减少重复在design及PCB Layout的测试及修正的过程及沟通时间，甚至透过最佳化的pin mapping、placement后可节省更多的走线空间或叠构。 Specifying Design Intent 在FSP整合工具内可直接由零件库选取要摆放的零件，而这些零件可直接使用PCB内的包装，预先让我们同步规划FPGA设计及在PCB的placement。
标签： Allegro Planner System FPGA
上传时间： 2013-10-19
上传用户：shaojie2080
PCB设计要点 一.PCB工艺限制 1）线 一般情况下，线与线之间和线与焊盘之间的距离大于等于13mil，实际应用中，条件允许时应考虑加大距离；布线密度较高时，可考虑但不建议采用IC脚间走两根线，线的宽度为10mil，线间距不小于10mil。特殊情况下，当器件管脚较密，宽度较窄时，可按适当减小线宽和线间距。 2）焊盘 焊盘与过渡孔的基本要求是：盘的直径比孔的直径要大于0.6mm；例如，通用插脚式电阻、电容和集成电路等，采用盘/孔尺寸 1.6mm/0.8mm（63mil/32mil），插座、插针和二极管1N4007等，采用1.8mm/1.0mm（71mil/39mil）。实际应用中，应根据实际元件的尺寸来定，有条件时，可适当加大焊盘尺寸；PCB板上设计的元件安装孔径应比元件管脚的实际尺寸大0.2～0.4mm左右。 3）过孔 一般为1.27mm/0.7mm(50mil/28mil)；当布线密度较高时，过孔尺寸可适当减小，但不宜过小，可考虑采用1.0mm/0.6mm(40mil/24mil)。 二.网表的作用 网表是连接电气原理图和PCB板的桥梁。是对电气原理图中各元件之间电气连接的定义，是从图形化的原理图中提炼出来的元件连接网络的文字表达形式。在PCB制作中加载网络表，可以自动得到与原理图中完全相
标签： PCB
上传时间： 2013-10-11
上传用户：13817753084
有时候，做元件封装的时候，做得不是按中心设置为原点（不提倡这种做法），所以制成之后导出来的坐标图和直接提供给贴片厂的要求相差比较大。比如，以元件的某一个pin 脚作为元件的原点，明显就有问题，直接修改封装的话，PCB又的重新调整。所以想到一个方法：把每个元件所有的管脚的X坐标和Y坐标分别求平均值，就为元件的中心。
上传时间： 2014-01-09
上传用户：xzt
1N4678~1N4717
上传时间： 2013-12-22
上传用户：tuilp1a
