分析了调幅信号和载波信号之间的相位差与调制信号的极性的对应关系,得出了相敏检波电路输出电压的极性与调制信号的极性有对应关系的结论。为了验证相敏检波电路的这一特性,给出3 个电路方案,分别选用理想元件和实际元件,采用Multisim 对其进行仿真实验,直观形象地演示了相敏检波电路的鉴相特性,是传统的实际操作实验所不可比拟的。关键词:相敏检波;鉴相特性;Multisim;电路仿真 Abstract : The corresponding relation between modulation signal polarity and difference phases of amplitudemodulated signal and the carrier signal ,the polarity of phase2sensitive detecting circuit output voltage and the polarity of modulation signal are correspondent . In order to verify this characteristic ,three elect ric circuit s plans are produced ,idea element s and actual element s are selected respectively. Using Multisim to carry on a simulation experiment ,and then demonst rating the phase detecting characteristic of the phase sensitive circuit vividly and directly. Which is t raditional practical experience cannot be com pared.Keywords :phase sensitive detection ;phase2detecting characteristic ;Multisim;circuit simulation
上传时间： 2013-11-23
上传用户：guanhuihong
本文提出用级联多电平逆变器取代变压器多重化结构的STATCOM 拓扑结构，用载波相移正弦脉宽调制技术(Carrier phase-shifted SPWM，以下简称CPS-SPWM)取代工频调制。这种基于CPS-SPWM 级联多电平逆变器的STATCOM 不仅去掉了多重化变压器，而且用较低的开关频率可以获得较高的等效开关频率的输出效果，简化了滤波；针对电力系统强耦合、非线性的特征，本文提出了将自抗扰控制应用于STATCOM 装置的控制策略，此控制策略不但可以大大缩短动态过程，改善系统的动态性能，而且具有较强的鲁棒性。
上传时间： 2013-11-20
上传用户：maqianfeng
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sense resistor. Inductor DCR sensingincreases effi ciency—especially at heavy load—whilereducing component cost and required board space.The LTC®3856 single-output 2-phase synchronous buckcontroller improves the accuracy of inductor DCR sensingby compensating for changes in DCR due to temperature.
上传时间： 2013-11-05
上传用户：guobing703
As logic systems get larger and more complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
上传时间： 2013-10-08
上传用户：zhqzal1014
该系统由单片机89S52控制模块，程控宽带放大模块，整形模块，FPGA内频率、相位差测量模块等构成，采用等精度测频法测出频率和周期，可测量有效值为0.01～5V，频率范围1Hz～20MHz信号的频率、周期信号，精度高达10-6。采用计数法测量相位差，该系统可测量有效值0.5～5V，频率10Hz～100kHz信号的相位差，精度为1°。系统功能由按键控制，测量结果实时显示，人机界面友好。 Abstract: The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
上传时间： 2013-11-04
上传用户：CHINA526
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
上传时间： 2014-12-04
上传用户：axin881314
MCU(单片机)对可控硅的控制:交流市电控制――ＭＣＵ对可控硅的控制 郭江辛 07-23-03在用可控硅对交流市电控制中，主要注意以下几个方面：一， 同步信号 （弄不好都会产生不均匀的斩波，控制白炽灯表现为灯闪）1) 清楚同步信号在交流周期中的位置,最好在交流零点选取.在一些阻容降压对MCU 供电电路中,最好直接在交流电源两端取同步信号（过零点）,以避免计算阻容产生的象移(PHASE SHIFT)2) 同步信号要稳定二， 控制信号 （弄不好则可控硅不能通，或一直通）1） 可控硅断路时，可控硅控制极（GATE）最好是开路，没有开极的MCU可加如下电路：
上传时间： 2014-05-05
上传用户：comer1123
