This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
本文主要讲述开关电源的基本制作原理及相关PCB电路的设计技巧，是做电源新手必备的基础知识
上传时间： 2014-01-01
上传用户：blans
如何在PCB的设计中注意到电磁兼容的问题，这里有你需要的问题
上传时间： 2013-11-25
上传用户：jcljkh
针对多层线路板中射频电路板的布局和布线，根据本人在射频电路PCB设计中的经验积累，总结了一些布局布线的设计技巧。并就这些技巧向行业里的同行和前辈咨询，同时查阅相关资料，得到认可，是该行业里的普遍做法。多次在射频电路的PCB设计中采用这些技巧，在后期PCB的硬件调试中得到证实，对减少射频电路中的干扰有很不错的效果，是较优的方案。
上传时间： 2013-10-21
上传用户：467368609
资料介绍说明： 软件名称：四层板PCB设计原理 文件大小 647KB 文件格式： rar 软件语言：共享资料 软件语言：简体中文 运行环境：WINXP WIN2003 WINME WIN9X 四层板PCB设计原理有protel 99se原理图，原图DSP.pcb,布局完成后的PCB，设计完成后的PCB，添加内电层后的PCB，信号线完成后的PVB 原理图有.analog.sch，CAN.sch，DSPCPLD.SCH，dsp pcb.等等 设计完成后的pcb档案
上传时间： 2013-11-22
上传用户：kxyw404582151
资料介绍说明： 软件名称：四层板PCB设计原理 文件大小 647KB 文件格式： rar 软件语言：共享资料 软件语言：简体中文 运行环境：WINXP WIN2003 WINME WIN9X 四层板PCB设计原理有protel 99se原理图，原图DSP.pcb,布局完成后的PCB，设计完成后的PCB，添加内电层后的PCB，信号线完成后的PVB 原理图有.analog.sch，CAN.sch，DSPCPLD.SCH，dsp pcb.等等 设计完成后的pcb档案
上传时间： 2013-11-08
上传用户：498732662
pcb阻抗设计必备
上传时间： 2013-10-20
上传用户：名爵少年
针对多层线路板中射频电路板的布局和布线，根据本人在射频电路PCB设计中的经验积累，总结了一些布局布线的设计技巧。并就这些技巧向行业里的同行和前辈咨询，同时查阅相关资料，得到认可，是该行业里的普遍做法。多次在射频电路的PCB设计中采用这些技巧，在后期PCB的硬件调试中得到证实，对减少射频电路中的干扰有很不错的效果，是较优的方案。
上传时间： 2013-10-26
上传用户：arnold
PCB设计
上传时间： 2015-01-01
上传用户：mpquest
PCB的规范原则细则
标签： pcb
上传时间： 2013-11-13
上传用户：HZB20416
