The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
The CAT9534 is an 8-bit parallel input/output portexpander for I²C and SMBus compatible applications.These I/O expanders provide a simple solution inapplications where additional I/Os are needed: sensors,power switches, LEDs, pushbuttons, and fans.The CAT9534 consists of an input port register, anoutput port register, a configuration register, a polarityinversion register and an I²C/SMBus-compatible serialinterface.
上传时间： 2013-11-09
上传用户：liulinshan2010
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上传时间： 2013-10-21
上传用户：xiaozhiqban
（Portmon is an application that lets you monitor serial and parallel activity on your local system, or any computer on the network that you can reach via TCP/IP. It is the most powerful tool available for tracking down port-related configuration problems and analyzing application port usage.）
上传时间： 2013-11-07
上传用户：1412904892
中文版详情浏览：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
标签： UltraScale Xilinx 架构
上传时间： 2013-11-13
上传用户：瓦力瓦力hong
本应用指南讲述一种实用的 MicroBlaze™ 系统，用于在非易失性 Platform Flash PROM 中存储软件代码、用户数据和配置数据，以简化系统设计和降低成本。另外，本应用指南还介绍一种可移植的硬件设计、一个软件设计以及在实现流程中使用的其他脚本实用工具。 简介许多 FPGA 设计都集成了使用 MicroBlaze 和 PowerPC™ 处理器的软件嵌入式系统，这些设计同时使用外部易失性存储器来执行软件代码。使用易失性存储器的系统还必须包含一个非易失性器件，用来在断电期间存储软件代码。大多数 FPGA 系统都在电路板上使用 Platform FlashPROM (在本文中称作 PROM)，用于在上电时加载 FPGA 配置数据。另外，许多应用还可能使用其他非易失性器件(如 SPI Flash、Parallel Flash 或 PIC)来保存 MAC 地址等少量用户数据，因此导致系统电路板上存在大量非易失性器件。
标签： MicroBlaze Platform Flash XAPP
上传时间： 2013-10-13
上传用户：hakim
为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2014-01-13
上传用户：qoovoop
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上传时间： 2013-11-05
上传用户：Wwill
The NXP LPC314x combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, three channel10-bit A/D, and a myriad of serial and parallel interfaces in a single chip targeted atconsumer, industrial, medical, and communication markets. To optimize system powerconsumption, the LPC314x have multiple power domains and a very flexible ClockGeneration Unit (CGU) that provides dynamic clock gating and scaling.
上传时间： 2013-10-11
上传用户：yuchunhai1990
