Many complex systems—such as telecom equipment,memory modules, optical systems, networking equipment,servers and base stations—use FPGAs and otherdigital ICs that require multiple voltage rails that muststart up and shut down in a specific order, otherwise theICs can be damaged. The LTC®2924 is a simple andcompact solution to power supply sequencing in a 16-pinSSOP package (see Figures 1 and 2).
上传时间： 2013-10-29
上传用户：tonyshao
Switching regulators are of universal interest. LinearTechnology has made a major effort to address this topic.A catalog of circuits has been compiled so that a designengineer can swiftly determine which converter type isbest. This catalog serves as a visual index to be browsedthrough for a specific or general interest.
标签： Collection Switching Regulator Circuit
上传时间： 2013-11-09
上传用户：mh_zhaohy
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
标签： 数字电源
上传时间： 2013-10-16
上传用户：dddddd
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
设计一种基于P89V51RD2的功率因数测量仪，采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心，大大简化系统硬件设计。而软件部分采用模块化设计思想，采用中值滤波和小数补偿算法，实现功率因数的高精度测量。实验测试表明，该功率因数测量仪测量精度高，运行稳定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上传时间： 2014-12-27
上传用户：CHINA526
针对目前燃气灶市场的状况，提出一种基于PIC16C711单片机的燃气灶脉冲点火控制器设计,具体包括有系统的组成和功能介绍、硬件电路设计及软件功能实现。 Abstract: Aiming at today’s gas cooker market, a pulse ignition controler design based on PIC16C711 is presented.The specific descriptions of system components and functions,hardware circuit design and software function are given.
上传时间： 2013-10-31
上传用户：zhqzal1014
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
