Linear 公司的LTC4310是绝缘的双向I2C总线通信器件，每个器件可把I2C逻辑状态编码成信号，通过绝缘层传输到另一个器件．接收器件解码，并驱动I2C总线到适当的确逻辑状态．主要用在绝缘的I2C, SMBus和PMBus 接口，绝缘电源，以太网供电和正到负电源通信．本文介绍了LTC4310主要特性，典型应用以及多种应用电路框图．
上传时间： 2013-11-02
上传用户：trepb001
为了实现把软件仿真的数据通过PCI总线DMA传输、处理后转换成高速视频串行数据流（LVDS数据流），设计出了基于PCI9054的数据转换模块。通过介绍PCI总线接口协议芯片PCI9054的性能、特点，分析了windows的WDM驱动程序的特点，在软硬件设计中采用把数据缓存器设置为两组SRAM的结构，两组SRAM交替进行数据存取的方式，有效克服了数据流不连续的现象，解决了形成不间断数据流和两次DMA传输之间的数据间断问题。应用结果表明，该设计可满足数字视频带宽20 MHz以内的LVDS数据流的转换与传输。
上传时间： 2014-12-26
上传用户：jisujeke
导读：本文介绍AVR官方唯一推荐的下载方法：STK500。也介绍了 AVR Studio 同时支持的JTAG下载。 并口下载由于速度很慢，AVR Studio 也不支持并口下载，(仅能使用第三方的软件下载) 故我们不推荐使用。 我们的感觉：用过STK500下载后，就不会再使用并口下载了。感觉是两种完全不同档次的方式。 预备知识1： AVR开发软件的选择与安装。 预备知识2： AVR Studio 快速入门 。 一：STK500 下载 支持的芯片：支持全系列的AVR芯片。并且，支持未来的AVR新芯片。 操作方法：打开 AVR Studio 软件，按下图操作。
上传时间： 2013-10-23
上传用户：非衣2016
基于单片机的住宅电子服务系统
上传时间： 2013-10-27
上传用户：yanyueshen
单片机通讯电路的抗干扰设计
上传时间： 2013-12-20
上传用户：jing911003
在开放式数控系统结构模型的基础上，研究了基于ISA总线的DSP通信控制原理。采用中断方式完成了PC机和DSP之间的通信。介绍了以DriverWorks为工具开发ISA设备WDM驱动程序的方法，探讨了中断处理、驱动程序与应用程序之间的通信,简要说明了驱动程序的安装与调试。通过调试,系统设计运行稳定。 Abstract: The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
上传时间： 2013-11-04
上传用户：kang1923
在汽车发动机起动时，若发动机起动后起动机不能及时断电，将会烧毁起动机或损坏飞轮齿环；若变速器不在空档位置起动，则起动机的瞬间动力将使汽车位移，还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器，通过检测汽车起动开关、变速箱档位、发动机转速，实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统，解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上传时间： 2013-10-15
上传用户：mikesering
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
