fpga open door,最最基础的入门介绍,针对首次接触此类的新手
上传时间: 2017-04-17
上传用户:gundan
VC+XML+UG OPEN API做的自动装配
上传时间: 2013-12-29
上传用户:zaizaibang
ecos RTOS 原理介绍和应用开发The design philosophy of eCos was to augment an open-source RTOS (which meant no per-unit royalties) with source-level con?guration tools that would enable embedded developers to scale their RTOS from hundreds of bytes to hundreds of kilobytes without needing to manu- ally change a line of source code.
标签: RTOS open-source philosophy augment
上传时间: 2013-12-16
上传用户:天涯
Alicebot and AIML Software Implementations The AI Foundation and our community has three open source free software "products" 1. The specification of the AIML language itself. 2. Various free software interpreters that implement (1). 3. The contents of the ALICE brain written in AIML (and other free AIML sets that exist).
标签: Implementations Foundation and community
上传时间: 2017-04-23
上传用户:jkhjkh1982
open source bios with linux platform, very good and can be reused.
标签: platform source reused linux
上传时间: 2017-04-25
上传用户:ayfeixiao
汇编程序所在目录ex2_asm 。 C 语言程序所在目录ex2_c 。 在CC2000 中的操作如下: 1. Project->Open ,打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN (快捷键F5) 即可看到最边上一个LED 周期性的闪亮。灯的闪烁频率由软件中的定时器Timer1 设置。这两个程序执行的功能是完全一样的。用户可以参考这两个文件作为其开发应用程序的模板。
上传时间: 2017-04-26
上传用户:璇珠官人
汇编程序所在目录ex2_asm 。 C 语言程序所在目录ex2_c 。 在CC2000 中的操作如下: 1. Project->Open ,打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN (快捷键F5) 即可看到最边上一个LED 周期性的闪亮。灯的闪烁频率由软件中的定时器Timer1 设置。这两个程序执行的功能是完全一样的。用户可以参考这两个文件作为其开发应用程序的模板。
上传时间: 2017-04-26
上传用户:hopy
程序所在目录:ex3_LED 打开CC2000,进行如下操作: 1. Project->Open ,打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN (快捷键F5) 可以看到的现象为:最边上一个LED 不断闪烁(这个LED 在后面其他的程序中都被定义成在定时器中断中闪烁)。其余的4 个LED 均处于熄灭状态。 现在将按键轻按一下,只有LED1 闪烁; 按第二下,只有LED2 闪烁; 按第三下,只有LED3 闪烁; 按第四下,只有LED4 闪烁; 按第五下,四个LED 循环依次闪烁。 若再按键,则如此反复循环。
上传时间: 2014-10-28
上传用户:我们的船长
程序所在目录:ex5_SPI D/A 转换芯片选用的是SPI 接口的TLC5620,串行4 通道8 位DA 转换。 打开CC2000,进行如下操作: 1.Project->Open ,打开该目录中的工程文件。 2.Project->Rebuild ALL,编译链接 3.File->Load Program 4.Debug->GO Main 5.Debug->RUN (快捷键F5) 用示波器可以看到DA_OUT1 接口输出三角波 DA_OUT2 输出三角波 用万用表可以测到DA_OUT3 输出2.475V DA_OUT4 输出1.65V 各路的DA 输出均由程序控制,用户可参照程序中的注释更改。
上传时间: 2017-04-26
上传用户:zhanditian
程序所在目录:ex_PWM 打开,进行如下操作: 1. Project->Open ,打开该目录中的工程文件。 2. Project->Rebuild ALL,编译链接 3. File->Load Program 4. Debug->Run 可以看到电机开始转动。本例程中PWM的频率是1KHZ ,输出的是两路带死去的PWM波形对。用户只需更改参数XPWM即可改变电机的转速和方向。该参数设置如下: XPWM=2400 最大值2500 When xpwm=0-900, 逆时针方向旋转,值越小,转速越快 When xpwm=1600-2500, 顺时针方向旋转,值越大,转速越快 When xpwm=900-1600,电机两端电压太低,基本上不足以起转。
上传时间: 2017-04-26
上传用户:jkhjkh1982