针对众多低成本数据采集需求，采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340，设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器，同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低，结构简单，体积小，已成功用于工业现场。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
上传时间： 2014-05-31
上传用户：1109003457
提出一种基于单片机AT89C51SND1C的MP3播放系统的设计方案。单片机集成了专用的解码器，使用K9F1208闪存作为外存储器，放音电路采用CS4330，存储文件通过播放器上的USB接口设备从PC机上直接下载，液晶显示采用LCD1602。方案设计简单，性价比高，低功耗，易扩展。由于采用的是通用单片机实现的，可以很容易地移植到其他微控制器系统中，有很强的市场竞争能力和实用价值。 Abstract: A MP3 player design based on microchip AT89C51SND1C was presented, which used K9F1208 Flash chip as the memory circuit and used CS4330 as play chip. Storage files were download from PC through USB interfaces player on the device，and the LCD/602 was used as display screen. This system had characteristics of simple design,low power,easy expand，low cost and high recognition. Using of universual microchip make it easy to transplant to other microcontrol system，and have strong market competitiom and practical value.
上传时间： 2014-12-27
上传用户：佳期如梦
The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
上传时间： 2013-11-20
上传用户：ynzfm
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
What is New in C51 Version 8.18[Device Support]Added debug support for the NXP P89LPC9408 in the LPC900 EPM Emulator/Programmer.[New Supported Device]Nuvoton W681308 device.[New Supported Device]NXP P89LPC9201, P89LPC9211, P89LPC922A1, P89LPC9241, P89LPC9251, P89LPC9301, P89LPC931A1, P89LPC9331, P89LPC9341, and P89LPC9351 devices.[New Supported Device]SiLabs C8051F500, C8051F501, C8051F504, C8051F505, C8051F506, C8051F507, C8051F508, C8051F509, C8051F510, and C8051F511 devices.[ULINK2 Support]Corrected potential deadlock on ST uPSD targets.[Device Simulation]Corrected simulation of Infineon XC800 MDU.[Device Simulation]Corrected behaviour of EXFn and TOGn on SiLabs C8051F12x/F13x devices.[Device Simulation]Added simulation for Atmel AT89C51RE2, including simulation of second UART.[Cx51 Compiler]Corrected failed initialization on far addresses when the object is located with _at_. 本资料仅供学习评估之用,请勿用于商业用途!请在学习评估24小时内删除.
上传时间： 2013-11-01
上传用户：panpanpan
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
