I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-Board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
标签： microcontro Using 76X LPC
上传时间： 2013-12-30
上传用户：Artemis
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew on-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上传时间： 2013-10-21
上传用户：xiaozhiqban
针对运行中火车测速运用多普勒效应采用DSP 设计雷达测速系统并阐述了其基本设计思想与工作原理给出系统硬件软件设计结构和原理图改善了原有光电测速精度提高了系统工作稳定性和可靠性经实验证明DSP 采集板工作稳定测速效果好关键词DSP; 雷达测速; 多普勒效应 On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
上传时间： 2013-10-27
上传用户：003030
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-Board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2014-08-16
上传用户：adada
The Maxim Integrated 71M6541-DB REV 3.0 Demo Board is a demonstration board for evaluating the 71M6541 device for single-phase electronic energy metering applications in conjunction with the Remote Sensor Inter-face. It incorporates a 71M6541 integrated circuit, a 71M6601 Remote Interface IC, peripheral circuitry such as a serial EEPROM, emulator port, and on-Board power supply. A serial to USB converter allows communication to a PC through a USB port. The Demo Board allows the evaluation of the 71M6541 energy meter chip for measurement accuracy and overall system use.
上传时间： 2013-11-06
上传用户：雨出惊人love
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-Board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2013-11-01
上传用户：wojiaohs
There are many manufacturers of dot matrix LCD modules. However, most of these displaysare similar. They all have on-Board controllers and drivers capable of displaying alpha numericsand a wide variety of other symbols (including Japanese "Katakana" characters). The internaloperation of LCD controller devices is determined by signals sent from a central processing unit(in this case, a CoolRunner-II CPLD).
标签： CoolRunner-II XAPP 904 LCD
上传时间： 2013-12-17
上传用户：haiya2000
Cypress Semiconductor makes a variety of PLL-based clock generators. This application note provides a set of recommendations to optimize usage of Cypress clock devices in a system. The application note begins with recommended termination techniques for clock generators. Subsequently, power supply filtering and bypassing is discussed. Finally, the application note provides some recommendations on board layout.
标签： Semiconductor application generators PLL-based
上传时间： 2013-12-20
上传用户：水中浮云
用AVR单片机设计的MP3播放器 功能： MP3 Player IDE ATA interface FAT 32 with long file name support USB interface On board power supply (input from 7v to 20v DC) Bootloader firmware upgradeable via USB port Infrared bi-directional interface Remote Control Back light graphic LCD worked with only 2x AA batteries In sleep mode sink less than 1uA (2.5mA in active mode) 5 buttons for easy navigation Long range (more than 20 feets)
标签： MP3 interface support Player
上传时间： 2016-07-02
上传用户：fandeshun
是英文 “ Surface mount technology ”的缩写。即表面安装技术，这是一种较传统的安装方式。其优点是可靠性高，缺点是体积大，成本高，限制 LCM 的小型化。 是英文 “ Chip On Board ”的缩写。即芯片被邦定(Bonding)在PCB上，由于IC制造商在LCD控制及相关芯片的生产上正在减小QFP（ SMT 的一种）封装的产量，因此，在今后的产品中传统的 SMT 方式将被逐步取代。
标签： technology Surface mount 英文
上传时间： 2016-10-08
上传用户：nairui21
