Stellaris(群星)单片机加上32KB串行SRAM(英) INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH LUMINARY MICRO PRODUCTS. NO LICENSE,EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THISDOCUMENT. EXCEPT AS PROVIDED IN LUMINARY MICRO’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS,LUMINARY MICRO ASSUMES NO LIABILITY WHATSOEVER, AND LUMINARY MICRO DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY, RELATING TO SALE AND/OR USE OF LUMINARY MICRO’S PRODUCTS INCLUDING LIABILITY OR WARRANTIESRELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHTOR OTHER INTELLECTUAL PROPERTY RIGHT. LUMINARY MICRO’S PRODUCTS ARE not INTENDED FOR USE IN MEDICAL,LIFE SAVING, OR LIFE-SUSTAINING APPLICATIONS.
上传时间： 2013-11-22
上传用户：lixqiang
1.The C Programming Language is a powerful, flexible andpotentially portable high-level programming language. 2.The C language may be used successfully to create a programfor an 8-bit MCU, but to produce the most efficient machinecode, the programmer must carefully construct the C Languageprogram.3.The programmer must not only create an efficient high leveldesign, but also pay attention to the detailed implementation.
上传时间： 2013-12-27
上传用户：huanglang
AT89C2051驱动步进电机的电路和源码:AT89C2051驱动步进电机的电路和源码 程序:stepper.c stepper.hex/* * STEPPER.C * sweeping stepper's rotor cw and cww 400 steps * Copyright (c) 1999 by W.Sirichote */＃i nclude c:\mc5151io.h /* include i/o header file */ ＃i nclude c:\mc5151reg.hregister unsigned char j,flag1,temp; register unsigned int cw_n,ccw_n;unsigned char step[8]={0x80,0xc0,0x40,0x60,0x20,0x30,0x10,0x90} #define n 400/* flag1 mask byte 0x01 run cw() 0x02 run ccw() */main(){ flag1=0; serinit(9600); disable(); /* no need timer interrupt */ cw_n = n; /* initial step number for cw */ flag1 |=0x01; /* initial enable cw() */while(1){ { tick_wait(); /* wait for 10ms elapsed */energize(); /* round-robin execution the following tasks every 10ms */ cw(); ccw(); } }}cw(){ if((flag1&0x01)!=0) { cw_n--; /* decrement cw step number */ if (cw_n !=0) j++; /* if not zero increment index j */ else {flag1&=~0x01; /* disable cw() execution */ ccw_n = n; /* reload step number to ccw counter */ flag1 |=0x02; /* enable cww() execution */ } }
上传时间： 2013-11-21
上传用户：boyaboy
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
上传时间： 2013-10-08
上传用户：18711024007
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this Apnote will explain themost common form of an external Interrupt request. This Apnote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.note: You will find additional information on how to setup the Interrupt System in theApnote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
