BGA布线指南 BGA CHIP PLACEMENT AND ROUTING RULE BGA是PCB上常用的组件，通常CPU、NORTH BRIDGE、SOUTH BRIDGE、AGP CHIP、CARD BUS CHIP…等，大多是以bga的型式包装，简言之，80﹪的高频信号及特殊信号将会由这类型的package内拉出。因此，如何处理BGA package的走线，对重要信号会有很大的影响。 通常环绕在BGA附近的小零件，依重要性为优先级可分为几类： 1. by pass。 2. clock终端RC电路。 3. damping（以串接电阻、排组型式出现；例如memory BUS信号） 4. EMI RC电路（以dampin、C、pull height型式出现；例如USB信号）。 5. 其它特殊电路（依不同的CHIP所加的特殊电路；例如CPU的感温电路）。 6. 40mil以下小电源电路组（以C、L、R等型式出现；此种电路常出现在AGP CHIP or含AGP功能之CHIP附近，透过R、L分隔出不同的电源组）。 7. pull low R、C。 8. 一般小电路组（以R、C、Q、U等型式出现；无走线要求）。 9. pull height R、RP。 中文DOC，共5页，图文并茂
上传时间： 2013-04-24
上传用户：cxy9698
MPC755 and MPC745 PowerPC microprocessors are high-performance, low-power, 32-bit implementations of
上传时间： 2013-05-27
上传用户：330402686
用fpga实现的DA转换器，有说明和源码，VDHL文件。\\r\\nA PLD Based Delta-Sigma DAC\\r\\nDelta-Sigma modulation is the simple, yet powerful,\\r\\ntechnique responsible for the extraordinary\\r\\nperformance and low cost of today s audio CD\\r\\nplayers. The simplest Delta-Sigm
上传时间： 2013-08-22
上传用户：dudu1210004
Abstract: This application note describes a new generation of digital-input Class D audio amplifiers that achieve high PSRRperformance, comparable to traditional analog Class D amplifiers. More importantly, these digital-input Class D amplifiersprovide additional benefits of reduced power, complexity, noise, and system cost.
上传时间： 2013-12-20
上传用户：JIUSHICHEN
Abstract: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间： 2013-10-25
上传用户：banyou
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
上传时间： 2013-12-23
上传用户：ArmKing88
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上传时间： 2013-10-09
上传用户：yepeng139
Abstract: Class D amplifiers are typically very efficient, making them ideal candidates for portable applications that require longbattery life and low thermal dissipation. However, electromagnetic interference (EMI) is an issue that commonly accompanies theClass D switching topology. Active-emissions limiting reduces radiated emissions and enables "filterless" operation, allowingdesigners to create small, efficient portable applications with low EMI.
上传时间： 2013-11-23
上传用户：哈哈hah
Abstract: Build a composite amplifier featuring high gain, wide bandwidth, good DC accuracy and low distortion
上传时间： 2014-12-23
上传用户：JasonC
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上传时间： 2013-10-28
上传用户：hanbeidang
