transimpedance linearization circuitry. This allows it to drive video loads with excellent differential gain and phase perfor mance on only 50 mW of power. The AD8001 is a current feedback amplifier and features gain flatness of 0.1 dB to 100 MHz while offering differential gain and phase error of 0.01% and 0.025°. This makes the AD8001 ideal for professional video electronics such as cameras and video switchers. Additionally, the AD8001’s low distortion and fast settling make it ideal for buffer high-speed A-to-D converters. The AD8001 offers low power of 5.5 mA max (VS = ±5 V) and can run on a single +12 V power supply, while being capable of delivering over 70 mA of load current. These features make this amplifier ideal for portable and battery-powered applications where size and power are critical. The outstanding bandwidth of 800 MHz along with 1200 V/µs of slew rate make the AD8001 useful in many general purpose high-speed applications where dual power supplies of up to ±6 V and single supplies from 6 V to 12 V are needed. The AD8001 is available in the industrial temperature range of –40°C to +85°C.
上传时间： 2020-04-21
上传用户：su1254
Electric distribution networks are critical parts of power delivery systems. In recent years, many new technologies and distributed energy resources have been inte- grated into these networks. To provide electricity at the possible lowest cost and at required quality, long-term planning is essential for these networks. In distribution planning, optimal location and size of necessary upgrades are determined to satisfy the demand and the technical requirements of the loads and to tackle uncertainties associated with load and distributed energy resources.
标签： Distribution Electric Planning Network
上传时间： 2020-06-07
上传用户：shancjb
The solid high-polymer-film-type fuel cell (PEM-FC) system is used as the power supply equipment for transportation and replaces an internal combustion engine. A reduction of the environmental load is expected through the cogeneration system’s (CGS) use of the PEM-FC system as a distributed power supply to individual houses, apartments, and so forth [1–3]. The growing use of distributed power systems, such as fuel cells, the reduction of power-transmission losses, and an increase of waste heat recovery are expected. Therefore, the reduction of carbon- dioxide emission is also expected as compared to conventional energy supply methods using commercial electric power.
标签： Micro-grids Fuel Cell
上传时间： 2020-06-07
上传用户：shancjb
Battery systems for energy storage are among the most relevant technologies of the 21 st century. They – in particular modern lithium-ion batteries (LIB) – are enablers for the market success of electric vehicles (EV) as well as for stationary energy storage solutions for balancing fluctuations in electricity grids resulting from the integrationofrenewableenergysourceswithvolatilesupply 1 .BothEVandstationary storage solutions are important because they foster the transition from the usage of fossil energy carriers towards cleaner renewable energy sources. Furthermore, EV cause less local air pollution and noise emissions compared to conventional combustion engine vehicles resulting in better air quality especially in urban areas. Unfortunately, to this day, various technological and economic challenges impede a broad application of batteries for EV as well as for large scale energy storage and load leveling in electricity grids.
标签： Multiscale Simulation Approach
上传时间： 2020-06-07
上传用户：shancjb
This design uses Common-Emitter Amplifier (Class A) with 2N3904 Bipolar Junction Transistor. Use “Voltage Divider Biasing” to reduce the effects of varying β (= ic / ib) (by holding the Base voltage constant) Base Voltage (Vb) = Vcc * [R2 / (R1 + R2)] Use Coupling Capacitors to separate the AC signals from the DC biasing voltage (which only pass AC signals and block any DC component). Use Bypass Capacitor to maintain the Q-point stability. To determine the value of each component, first set Q-point close to the center position of the load line. (RL is the resistance of the speaker.)
上传时间： 2020-11-27
上传用户：
使用说明 ：1， 解压文件。2，打开PADS 软件， 依次点选 tools basicscripts ,basicscripts,load file, 选取PcbPartLocation.BAS 文件， 点选 RUN 。大功告成（ 注意PADS 位号字体相同）
标签： pads
上传时间： 2021-11-04
上传用户：XuVshu
Wide 2.2V to 6V Input Voltage Range 0.20V FB adjustable LED drive current Directly drive 9 Series 1W LED at VIN>=6V Fixed 800KHz Switching Frequency Max. 3A Switching Current Capability Up to 92% efficiency Excellent line and load regulation EN PIN TTL shutdown capability Internal Optimize Power MOSFET
标签： sc3633
上传时间： 2021-11-05
上传用户：d1997wayne
The PW5200A/ PW5200C is high efficiency synchronous, PWM step-up DC/DC converters optimizedto provide a high efficient solution to medium power systems. The devices work with a 1.4MHz fixedfrequency switching. These features minimize overall solution footprint by allowing the use of tiny,low profile inductors and ceramic capacitors. Automatic PWM/PFM mode switching at light loadsaves power and improves efficiency
标签： pw5200
上传时间： 2022-02-11
上传用户：
The PW3130 series product is a high integration solution for lithium-lion/polymer batteryprotection.PW3130 contains advanced power MOSFET, high-accuracy voltage detection circuits anddelay circuits. PW3130 is put into an ultra-small SOT23-5 package and only one external componentmakes it an ideal solution in limited space of battery pack. PW3130 has all the protection functionsrequired in the battery application including overcharging, overdischarging, overcurrent and loadshort circuiting protection etc. The accurate overcharging detection voltage ensures safe and fullutilization charging.The low standby current drains little current from the cell while in storage. Thedevice is not only targeted for digital cellular phones, but also for any other Li-Ion and Li-Polybattery-powered information appliances requiring long-term battery life
标签： pw3130
上传时间： 2022-02-11
上传用户：fliang
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
标签： pw2601
上传时间： 2022-02-11
上传用户：
