Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier Your
上传时间： 2013-11-13
上传用户：daoyue
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上传时间： 2013-11-23
上传用户：rocketrevenge
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
标签： Amplifier Low-Noise 2691 Band
上传时间： 2014-12-04
上传用户：zaocan888
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签： Circuitry Operation Single 1017
上传时间： 2013-12-20
上传用户：Wwill
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
标签： Converters Defini DAC
上传时间： 2013-10-30
上传用户：stvnash
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
本文将接续介绍电源与功率电路基板，以及数字电路基板导线设计。宽带与高频电路基板导线设计a.输入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器电路基板图26 是由FET 输入的高速OP 增幅器OPA656 构成的高输入阻抗OP 增幅电路，它的gain取决于R1、R2，本电路图的电路定数为2 倍。此外为改善平滑性特别追加设置可以加大噪讯gain，抑制gain-频率特性高频领域时峰值的R3。图26 高输入阻抗的宽带OP增幅电路图27 是高输入阻抗OP 增幅器的电路基板图案。降低高速OP 增幅器反相输入端子与接地之间的浮游容量非常重要，所以本电路的浮游容量设计目标低于0.5pF。如果上述部位附着大浮游容量的话，会成为高频领域的频率特性产生峰值的原因，严重时频率甚至会因为feedback 阻抗与浮游容量，造成feedback 信号的位相延迟，最后导致频率特性产生波动现象。此外高输入阻抗OP 增幅器输入部位的浮游容量也逐渐成为问题，图27 的电路基板图案的非反相输入端子部位无full ground设计，如果有外部噪讯干扰之虞时，接地可设计成网格状(mesh)。图28 是根据图26 制成的OP 增幅器gain－频率特性测试结果，由图可知即使接近50MHz频率特性非常平滑，-3dB cutoff频率大约是133MHz。
标签： PCB
上传时间： 2013-11-13
上传用户：hebanlian
模块电源的电气性能是通过一系列测试来呈现的，下列为一般的功能性测试项目，详细说明如下： 电源调整率(Line Regulation) 负载调整率(Load Regulation) 综合调整率(Conmine Regulation) 输出涟波及杂讯(Ripple & Noise) 输入功率及效率(Input Power, Efficiency) 动态负载或暂态负载(Dynamic or Transient Response) 起动(Set-Up)及保持(Hold-Up)时间 常规功能(Functions)测试 1. 电源调整率 电源调整率的定义为电源供应器于输入电压变化时提供其稳定输出电压的能力。测试步骤如下：于待测电源供应器以正常输入电压及负载状况下热机稳定后，分别于低输入电压(Min)，正常输入电压(Normal)，及高输入电压(Max)下测量并记录其输出电压值。 电源调整率通常以一正常之固定负载(Nominal Load)下，由输入电压变化所造成其输出电压偏差率(deviation)的百分比，如下列公式所示： [Vo(max)-Vo(min)] / Vo(normal) 2. 负载调整率 负载调整率的定义为开关电源于输出负载电流变化时，提供其稳定输出电压的能力。测试步骤如下：于待测电源供应器以正常输入电压及负载状况下热机稳定后，测量正常负载下之输出电压值，再分别于轻载(Min)、重载(Max)负载下，测量并记录其输出电压值(分别为Vo(max)与Vo(min))，负载调整率通常以正常之固定输入电压下，由负载电流变化所造成其输出电压偏差率的百分比，如下列公式所示： [Vo(max)-Vo(min)] / Vo(normal) 3. 综合调整率 综合调整率的定义为电源供应器于输入电压与输出负载电流变化时，提供其稳定输出电压的能力。这是电源调整率与负载调整率的综合，此项测试系为上述电源调整率与负载调整率的综合，可提供对电源供应器于改变输入电压与负载状况下更正确的性能验证。 综合调整率用下列方式表示：于输入电压与输出负载电流变化下，其输出电压之偏差量须于规定之上下限电压范围内(即输出电压之上下限绝对值以内)或某一百分比界限内。 4. 输出杂讯 输出杂讯(PARD)系指于输入电压与输出负载电流均不变的情况下，其平均直流输出电压上的周期性与随机性偏差量的电压值。输出杂讯是表示在经过稳压及滤波后的直流输出电压上所有不需要的交流和噪声部份(包含低频之50/60Hz电源倍频信号、高于20 KHz之高频切换信号及其谐波，再与其它之随机性信号所组成))，通常以mVp-p峰对峰值电压为单位来表示。 一般的开关电源的规格均以输出直流输出电压的1%以内为输出杂讯之规格，其频宽为20Hz到20MHz。电源实际工作时最恶劣的状况(如输出负载电流最大、输入电源电压最低等)，若电源供应器在恶劣环境状况下，其输出直流电压加上杂讯后之输出瞬时电压，仍能够维持稳定的输出电压不超过输出高低电压界限情形，否则将可能会导致电源电压超过或低于逻辑电路(如TTL电路)之承受电源电压而误动作，进一步造成死机现象。 同时测量电路必须有良好的隔离处理及阻抗匹配，为避免导线上产生不必要的干扰、振铃和驻波，一般都采用双同轴电缆并以50Ω于其端点上，并使用差动式量测方法(可避免地回路之杂讯电流)，来获得正确的测量结果。 5. 输入功率与效率 电源供应器的输入功率之定义为以下之公式： True Power = Pav(watt) = Vrms x Arms x Power Factor 即为对一周期内其输入电压与电流乘积之积分值，需注意的是Watt≠VrmsArms而是Watt=VrmsArmsxP.F.，其中P.F.为功率因素(Power Factor)，通常无功率因素校正电路电源供应器的功率因素在0.6～0.7左右，其功率因素为1～0之间。 电源供应器的效率之定义为为输出直流功率之总和与输入功率之比值。效率提供对电源供应器正确工作的验证，若效率超过规定范围，即表示设计或零件材料上有问题，效率太低时会导致散热增加而影响其使用寿命。 6. 动态负载或暂态负载 一个定电压输出的电源，于设计中具备反馈控制回路，能够将其输出电压连续不断地维持稳定的输出电压。由于实际上反馈控制回路有一定的频宽，因此限制了电源供应器对负载电流变化时的反应。若控制回路输入与输出之相移于增益(Unity gain)为1时，超过180度，则电源供应器之输出便会呈现不稳定、失控或振荡之现象。实际上，电源供应器工作时的负载电流也是动态变化的，而不是始终维持不变(例如硬盘、软驱、CPU或RAM动作等)，因此动态负载测试对电源供应器而言是极为重要的。可编程序电子负载可用来模拟电源供应器实际工作时最恶劣的负载情况，如负载电流迅速上升、下降之斜率、周期等，若电源供应器在恶劣负载状况下，仍能够维持稳定的输出电压不产生过高激(Overshoot)或过低(Undershoot)情形，否则会导致电源之输出电压超过负载组件(如TTL电路其输出瞬时电压应介于4.75V至5.25V之间，才不致引起TTL逻辑电路之误动作)之承受电源电压而误动作，进一步造成死机现象。 7. 启动时间与保持时间 启动时间为电源供应器从输入接上电源起到其输出电压上升到稳压范围内为止的时间，以一输出为5V的电源供应器为例，启动时间为从电源开机起到输出电压达到4.75V为止的时间。 保持时间为电源供应器从输入切断电源起到其输出电压下降到稳压范围外为止的时间，以一输出为5V的电源供应器为例，保持时间为从关机起到输出电压低于4.75V为止的时间，一般值为17ms或20ms以上，以避免电力公司供电中于少了半周或一周之状况下而受影响。 8. 其它 在电源具备一些特定保护功能的前提下，还需要进行保护功能测试，如过电压保护(OVP)测试、短路保护测试、过功保护等
上传时间： 2013-10-22
上传用户：zouxinwang
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
上传时间： 2014-11-30
上传用户：ynzfm
