本文依据集成电路设计方法学，探讨了一种基于标准Intel 8086 微处理器的单芯片计算机平台的架构。研究了其与SDRAM，8255 并行接口等外围IP 的集成，并在对AMBA协议和8086 CPU分析的基础上，采用遵从AMBA传输协议的系统总线代替传统的8086 CPU三总线结构，搭建了基于8086 IP 软核的单芯片计算机系统，并实现了FPGA 功能演示。关键词：微处理器； SoC；单芯片计算机；AMBA 协议 Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
上传时间： 2013-12-27
上传用户：kernor
KEIL RTX51实时操作系统中文版:RTX51是一个适用于8051 家族的实时多任务操作系统。RTX51使复杂的系统和软件设计以及有时间限制的工程开发变得简单。RTX51是一个强大的工具，它可以在单个CPU上管理几个作业（任务）。RTX51有两种不同的版本。 RTX51 Full 允许4个优先权任务的循环和切换，并且还能并行的利用中断功能。RTX51 支持信号传递，以及与系统邮箱和信号量进行消息传递。RTX51的os_wait 函数可以等以 下事件：中断、时间到、来自任务或中断的信号、来自任务或中断的消息、信号量。 RTX51 Tiny 是RTX51 Full 的一个子集。RTX51 Tiny 可以很容易的运行在没有扩展外 部存储器的单片机系统上。但是，使用RTX51 Tiny 的程序可以访问外部存储器。RTX51 Tiny允许循环任务切换，并且支持信号传递，还能并行的利用中断功能。RTX51 Tiny 的os_wait函数可以等待以下事件：时间到、时间间隔、来自任务或者中断的信号。 本章节以后的部分用RTX-51 来指代RTX-51 Full 和RTX-51 Tiny。在两者之间不同的 地方会加以说明。
上传时间： 2013-11-25
上传用户：axin881314
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
基于单片机的除尘控制器的设计:介绍通用控制仪的硬件组成和软件设计,阐述了系统的性能指标和功能特点。该产品功能完善,可靠性高,具有很好的应用前景。关键词: 除尘器;通用控制仪;单片机;系统设计 Abstract: The hardware structure and the software design are introduced in this paper, and the performance index and the features of the system are expounded. It has comp rehensive functions, high reliability and good app lication.Key words: dust catcher; universal controller; microcontroller; system design
上传时间： 2013-11-16
上传用户：ming52900
一种实用的微机自动配料秤系统:介绍一种由单片机构成的配料秤。叙述了秤的传感器、变送器、信号的变换、硬件原理、软件流程以及和DCS 系统构成的单回路调节系统,此系统可广泛地应用于各行业的配料控制中。关键词:配料秤 单片机 单回路调节系统 DCS 系统 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上传时间： 2013-10-12
上传用户：zwei41
基于单片机控制的二氧化碳浓度测试计:基于CDM4161二氧化碳气体浓度测试模块以及ATtiny26单片机,提出了一种二氧化碳浓度测试计的设计方案。该方案具有硬件电路简单、成本低、可靠性高、测量准确等优点，具有较高的实用价值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上传时间： 2013-11-14
上传用户：zjwangyichao
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
上传时间： 2013-11-04
上传用户：as275944189
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上传时间： 2014-04-03
上传用户：lizhizheng88
