本文将接续介绍电源与功率电路基板，以及数字电路基板导线设计。宽带与高频电路基板导线设计a.输入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器电路基板图26 是由FET 输入的高速OP 增幅器OPA656 构成的高输入阻抗OP 增幅电路，它的gain取决于R1、R2，本电路图的电路定数为2 倍。此外为改善平滑性特别追加设置可以加大噪讯gain，抑制gain-频率特性高频领域时峰值的R3。图26 高输入阻抗的宽带OP增幅电路图27 是高输入阻抗OP 增幅器的电路基板图案。降低高速OP 增幅器反相输入端子与接地之间的浮游容量非常重要，所以本电路的浮游容量设计目标低于0.5pF。如果上述部位附着大浮游容量的话，会成为高频领域的频率特性产生峰值的原因，严重时频率甚至会因为feedback 阻抗与浮游容量，造成feedback 信号的位相延迟，最后导致频率特性产生波动现象。此外高输入阻抗OP 增幅器输入部位的浮游容量也逐渐成为问题，图27 的电路基板图案的非反相输入端子部位无full ground设计，如果有外部噪讯干扰之虞时，接地可设计成网格状(mesh)。图28 是根据图26 制成的OP 增幅器Gain－频率特性测试结果，由图可知即使接近50MHz频率特性非常平滑，-3dB cutoff频率大约是133MHz。
标签： PCB
上传时间： 2013-11-13
上传用户：hebanlian
The LTP5900 includes sufficient power supply filtering and decoupling capacitancesuch that additional filtering should not be necessary for most battery-powereddesigns. Care must be taken to avoid large transient voltages on the supply as theM2510 steps up its current consumption (see the section on Supply Design below).
标签： Integration Hardware Guide 5900
上传时间： 2014-12-24
上传用户：youmo81
The LTP5901 and LTP5902 require little external circuitry, as the devices references,decoupling and power supply filtering are integrated. The LTP5901 and LTP5902 will bemodularly certified for operation in the United States (FCC), Canada (IC) and theEuropean Union (CE).
标签： Integration LTP Hardware Guide
上传时间： 2013-11-22
上传用户：sunchao524
We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.
上传时间： 2013-10-15
上传用户：lz4v4
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
标签： MAXREFDES Lakewood Isolated Output
上传时间： 2013-11-02
上传用户：fengzimili
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
标签： Riverside MAXREFDES Isolated Output
上传时间： 2013-11-16
上传用户：会稽剑客
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上传时间： 2013-10-12
上传用户：jinyao
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
标签： 数字电源
上传时间： 2013-10-16
上传用户：dddddd
Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
标签： Switchin Output Single SKS
上传时间： 2013-10-30
上传用户：taa123456
