介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心，基于标准的USB1.1协议，设计一种通用USB接口模块，以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间： 2014-01-08
上传用户：赵云兴
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
This is the Xilinx Dual Processor Reference Designs suite. The designs illustrate a few differentdual-core architectures based on the MicroBlaze™ and PowerPC™ processors. The designsillustrate various concepts described in the Xilinx White Paper WP262 titled, “DesigningMultiprocessor Systems in Platform Studio”. There are simple software applications includedwith the reference designs that show various forms of interaction between the two processors.
上传时间： 2013-10-29
上传用户：旭521
When I started writing the first edition of RF Power Amplifiers for Wireless Communications,some time back in 1997, it seemed that I was roaming a largely uninhabitedlandscape. For reasons still not clear to me there were few, if any, otherbooks dedicated to the subject of RF power amplifiers. Right at the same time, however,hundreds of engineers were being assigned projects to design PAs for wirelesscommunications products. It was not, therefore, especially difficult to be successfulwith a book that was fortuitously at the right place and the right time.
标签： Communications Amplifiers Wireless Edition
上传时间： 2013-11-12
上传用户：YYRR
Digital cameras have become increasingly popular over the last few years. Digital imagingtechnology has grown to new markets including cellular phones and PDA devices. With thediverse marketplace, a variety of imaging technology must be available. Imaging technologyhas expanded to include both charge-coupled device (CCD) and CMOS image sensors.
标签： CoolRunner-II XAPP CPLD 390
上传时间： 2013-10-16
上传用户：18710733152
In this paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level simulation mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this paper, however,here we try to cover a few of them.
标签： Efficient Verilog Digital Coding
上传时间： 2013-11-23
上传用户：我干你啊
