用计数器中断实现100以内的按键计数
上传时间: 2013-10-09
上传用户:dazhihui66
针对一般测温方法在进行流体多点温度测量时存在系统复杂,准确度和速度难以兼顾的问题,提出了一种基于温度-频率(T-F)变换的测量系统。该系统使用PIC18F6722单片机控制MOS管开关阵列,使多个测点的热敏电阻分别与TLC555构成振荡电路,将测点的温度变化转化为振荡频率的变化,使用8253计数芯片对TLC555的输出信号进行测量并产生中断,单片机读取8253计数值反演为测点温度。实验表明,测点数目增多不会增加测量系统的复杂程度,通过设置8253的计数初值,可以在不改变硬件的情况下灵活选择测量的准确度和速度,满足了流体多点精确快速测温的需求。同时该系统具备简洁实用,成本低的优点。
上传时间: 2013-10-23
上传用户:assef
指南描述了如何实现小型且高速的中断驱动步进马达控制器
上传时间: 2014-06-15
上传用户:Breathe0125
代码说明了一个ps2口驱动和编程方法。主要是鼠标,当鼠标产生中断时,主板上的蜂鸣器和运行灯都有反映。移动鼠标或点击鼠标的左右键,发现主板有反映。注意,因为程序并没有驱动滚轮,所以鼠标滚轮不能产生中断。
上传时间: 2015-03-12
上传用户:weixiao99
普通IO口模拟RS232串口 占用定时器0中断 在TH0,TL0中设置波特率的大小 注意不要开定时器0的中断,这里用的是查询方式
上传时间: 2014-01-12
上传用户:Amygdala
1.初始化程序时候,获取本机的拨号连接 2.拨号时候,利用选择的拨号连接进行拨号 3.成功后提示connected.点击OK挂断. 4.注意程序中用户名和密码的设定.
上传时间: 2013-12-09
上传用户:牛布牛
基于UCOS的中断处理程序 当按键按下时,相应的外部中断触发产生 执行处理程序
上传时间: 2014-01-25
上传用户:集美慧
在WinCE系统中应用程序直接获取中断触发和直接操作I/O口,进行读取和写入。从而减少驱动程序的开发
上传时间: 2015-06-06
上传用户:jcljkh
F2812 标准FFT算法,128点,256点,512点,1024点FFT算法,具体做法为将库含数FFT.LIB加入的目标项目,加入对应的C含数和头文件,特别注意的FFT算法缓冲去一定要存放在0X8000H中的内部缓冲区中!!!切记,本人调试时就走了很多弯路啊
上传时间: 2014-02-15
上传用户:康郎
文件中主要包含的内容为: AT91RM9200的内部内部功能寄存器的定义,ROMSTART.S(ARM)复位启动涵数 网络接口操作(物理转接芯片为:9161读者注意)、初始化、中断等功能
上传时间: 2015-06-14
上传用户:asddsd