摘要：本水位监测报警器使用5V低压直流电源（也可以用3节5号电池代替）就可以对5~15厘米的水位进行监测，用LED显示和数码管显示水位，并可以对不再此范围内的水位发出报警。主要采用CD4066、74LS86、74LS32、CD4511芯片，再加上数码管、蜂鸣器、发光二极管、电阻这些器件组成一个简单而灵敏的监测报警电路，操作简单，接通电源即可工作。因为大部分电路采用数字电路，所以本水位监测报警器还具有耗能低、准确性高的特点。关键字：译码电路 报警电路 监测电路 Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics. Keyword: Decoding circuit alarm circuit monitoring circuit
上传时间： 2013-11-05
上传用户：王庆才
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2014-08-16
上传用户：adada
Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The core voltages, VCCINT, for most Xilinx FPGAs, rangefrom 1.2V to 2.5V. Some mature products have 3V, 3.3Vor 5V core voltages. Table 1 shows the core voltagerequirement for most of the FPGA device families. TypicalI/O voltages (VCCO) vary from 1.2V to 3.3V. The auxiliaryvoltage VCCAUX is 2.5V for Virtex-II Pro and Spartan-3, andis 3.3V for Virtex-II.
上传时间： 2013-10-22
上传用户：liu999666
机电类比法是一种把机械量通过一定的计算等效类比为电量的方法，其在对电子机械系统的分析中应用非常广泛。它能够把一个较复杂的机械系统类比为我们熟知的电路系统来进行分析，从而使问题的分析得到简化。本文通过对振弦式传感器的分析介绍了机电类比法，并对使用电路进行了相关的分析。 Summary：The electromechanical analogy is assort of analysis which is to analogize the mechanical system by using circuit system , it applied widely in the filed of analysis the electronic-mechanical system. The analysis can take a complex mechanical system analogous to a circuitry that we well-known, which can simplify the problems. In the paper, the electro-mechanical analogy method is briefly introduced by analysis the vibrating wire sensor，and have a correlation analysis about the circuit we used.关键词： 机电类比法 振弦式传感器 频率 振荡 反馈Keyword：electro-mechanical analogy method，vibrating wire sensor，frequency, oscillation, feedback 0 引言振弦式传感器是属于频率式传感器的一种。所谓频率式传感器就是能直接将被测量转换为振动频率信号的传感器，这类传感器一般是通过测量振弦、振筒、振梁、振膜等弹性振体或石英晶体谐振器的固有谐振频率来达到测量引起谐振频率变化的被测非电量的目的，其也称为谐振式传感器[1]。在分析该类传感器中，由于其涉及到频率，就容易让人联想到在电子技术中接触到的RLC振荡电路。因此可以尝试着用类比的方法使之对应起来分析,即机电类比法分析。
上传时间： 2013-11-16
上传用户：paladin
The Maxim Integrated 71M6541-DB REV 3.0 Demo Board is a demonstration board for evaluating the 71M6541 device for single-phase electronic energy metering applications in conjunction with the Remote Sensor Inter-face. It incorporates a 71M6541 integrated circuit, a 71M6601 Remote Interface IC, peripheral circuitry such as a serial EEPROM, emulator port, and on-board power supply. A serial to USB converter allows communication to a PC through a USB port. The Demo Board allows the evaluation of the 71M6541 energy meter chip for measurement accuracy and overall system use.
上传时间： 2013-11-06
上传用户：雨出惊人love
Abstract: This application note illustrates the flexibility of the MAX7060 ASK/FSK transmitter. While the currently available evaluationkit (EV kit) has been optimized for the device's use in a specific frequency band (i.e., 288MHz to 390MHz), this document addresseshow the EV kit circuitry can be modified for improved operation at 433.92MHz, a frequency commonly used in Europe. Twoalternative match and filter configurations are presented: one for optimizing drain efficiency, the other for achieving higher transmitpower. Features and capabilities of earlier Maxim industrial, scientific, and medical radio-frequency (ISM-RF) transmitters areprovided, allowing comparison of the MAX7060 to its predecessors. Several design guidelines and cautions for using the MAX7060are discussed.
上传时间： 2013-11-14
上传用户：swaylong
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2013-11-01
上传用户：wojiaohs
Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The core voltages, VCCINT, for most Xilinx FPGAs, rangefrom 1.2V to 2.5V. Some mature products have 3V, 3.3Vor 5V core voltages. Table 1 shows the core voltagerequirement for most of the FPGA device families. TypicalI/O voltages (VCCO) vary from 1.2V to 3.3V. The auxiliaryvoltage VCCAUX is 2.5V for Virtex-II Pro and Spartan-3, andis 3.3V for Virtex-II.
上传时间： 2013-10-22
上传用户：aeiouetla
The power of programmability gives industrial automation designers a highly efficient， cost-effective alternative to traditional motor control units （MCUs）。 The parallel-processing power， fast computational speeds， and connectivity versatility of Xilinx® FPGAs can accelerate the implementation of advanced motor control algorithms such as Field Oriented Control （FOC）。 Additionally， Xilinx devices lower costs with greater on-chip integration of system components and shorten latencies with high-performance digital signal processing （DSP） that can tackle compute-intensive functions such as PID Controller， Clark/Park transforms， and Space Vector PWM. The Xilinx Spartan®-6 FPGA Motor Control Development Kit gives designers an ideal starting point for evaluating time-saving， proven， motor-control reference designs. The kit also shortens the process of developing custom control capabilities， with integrated peripheral functions （Ethernet， PowerLink， and PCI® Express）， a motor-control FPGA mezzanine card （FMC） with built-in Texas Instruments motor drivers and high-precision Delta-Sigma modulators， and prototyping support for evaluating alternative front-end circuitry.
上传时间： 2013-10-28
上传用户：wujijunshi
