although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
上传时间： 2013-11-04
上传用户：qq10538412
Specifying the right reference and applying it correctly isa more difficult task than one might first surmise, consideringthat references are only 2- or 3-terminal devices.although the word “accuracy” is most often spoken inreference to references, it is dangerous to use this wordtoo freely because it can mean different things to differentpeople. Even more perplexing is the fact that a referenceclassified as a dog in one application is a panacea inanother. This application note will familiarize the readerwith the various aspects of reference “accuracy” andpresent some tips on extracting maximum performancefrom any reference.
标签： 电压基准
上传时间： 2013-10-15
上传用户：liuwei6419
A frequent requirement in systems involves drivinganalog signals into non-linear or reactive loads. Cables,transformers, actuators, motors and sample-hold circuitsare examples where the ability to drive diffi cult loads isrequired. although several power buffer amplifi ers areavailable, none have been optimized for driving diffi cultloads.
上传时间： 2014-12-24
上传用户：1109003457
Size, output flexibility and efficiency advantages havemade switching regulators common in electronic apparatus.The continued emphasis on these attributes hasresulted in circuitry with 95% efficiency that requiresminimal board area. although these advantages are welcome,they necessitate compromising other parameters
上传时间： 2013-11-04
上传用户：zycidjl
A large group of fiber optic lasers are powered by DCcurrent. Laser drive is supplied by a current source withmodulation added further along the signal path. Thecurrent source, although conceptually simple, constitutesan extraordinarily tricky design problem. There are anumber of practical requirements for a fiber optic currentsource and failure to consider them can cause laser and/or optical component destruction.
上传时间： 2013-10-30
上传用户：wanghui2438
This ink marks LTC’s eighth circuit collection publication.1We are continually surprised, to the point of near mystification, by these circuit amalgams seemingly limitlessappeal. Reader requests ascend rapidly upon publication,remaining high for years, even decades. All LTC circuitcollections, despite diverse content, share this popularity,although just why remains an open question. Why isit? Perhaps the form; compact, complete, succinct andinsular. Perhaps the freedom of selection without commitment,akin to window shopping.
上传时间： 2014-01-06
上传用户：ligi201200
This application note describes how to decode standard DTMF tones using the minimum number of external discrete components and a PIC. The two examples use a PIC which has an 8 bit timer and either a comparator or an ADC, although it can be modified for use on a PIC which has only digital I/O. The Appendices have example code for the 16C662 (with comparator) and 16F877 (using the ADC). As the majority of the Digital Signal Processing is done in software, little is required in the way of external signal conditioning. Software techniques are used to model the individual elements of a DTMF Decoder IC.
上传时间： 2013-11-21
上传用户：zhaoke2005
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
This document was developed under the Standard Hardware and Reliability Program (SHARP) TechnologyIndependent Representation of Electronic Products (TIREP) project. It is intended for use by VHSIC HardwareDescription Language (VHDL) design engineers and is offered as guidance for the development of VHDL modelswhich are compliant with the VHDL Data Item Description (DID DI-EGDS-80811) and which can be providedto manufacturing engineering personnel for the development of production data and the subsequent productionof hardware. Most VHDL modeling performed to date has been concentrated at either the component level orat the conceptual system level. The assembly and sub-assembly levels have been largely disregarded. Under theSHARP TIREP project, an attempt has been made to help close this gap. The TIREP models are based upon lowcomplexity Standard Electronic Modules (SEM) of the format A configuration. although these modules are quitesimple, it is felt that the lessons learned offer guidance which can readily be applied to a wide range of assemblytypes and complexities.
上传时间： 2013-11-20
上传用户：pzw421125
