虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

all-In-one

  • 模拟IC性能的权衡 模拟到数字化设计的挑战

    Abstract: Many digital devices incorporate analog circuits. For instance, microprocessors, applicationspecificintegrated circuits (ASICs), and field-programmable gate arrays (FPGAs) may have internalvoltage references, analog-to-digital converters (ADCs) or digital-to-analog converters (DACs). However,there are challenges when you integrate more analog onto a digital design. As with all things in life, inelectronics we must always trade one parameter for another, with the application dictating the propertrade-off of analog function. In this application note, we examine how the demand for economy of spaceand cost pushes analog circuits onto digital substrates, and what design challenges emerge.  

    标签: 模拟IC 性能 模拟 数字化设计

    上传时间: 2013-11-17

    上传用户:菁菁聆听

  • RF至数字接收器的信号链噪声分析

      Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.

    标签: 数字接收器 信号链 噪声分析

    上传时间: 2014-12-05

    上传用户:cylnpy

  • 高速数字系统设计下载pdf

    高速数字系统设计下载pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.

    标签: 高速数字 系统设计

    上传时间: 2013-10-26

    上传用户:缥缈

  • Design Safe Verilog State Machine(Synplicity)

      One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a highly optimal final implementation of the state machine.

    标签: Synplicity Machine Verilog Design

    上传时间: 2013-10-23

    上传用户:司令部正军级

  • 高效LCD液晶照明技术

    In August of 1992 LTC published Application Note 49, “Illumination Circuitry for Liquid Crystal Displays.” One notable aspect of this event is that it generated more response than all previous LTC application notes combined. This level of interest, along with significant performance advances since AN-49’s appearance, justifies further discussion of LCD backlighting circuitry.

    标签: LCD 液晶 照明技术

    上传时间: 2013-11-19

    上传用户:lanjisu111

  • 电网现场作业管理系统的信息化设计

    为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行,信息不能共享,功能、效率受限,建设和维护成本高的现状,提出了采用B/S+C/S构架模式,将各现场作业管理模块和生产MIS(管理系统)集成为一体的现场作业管理系统的设计方案,做到各子系统和生产MIS软硬资源共享,做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统,各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用,目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract:  In order to improve the status that the substation field inspection system, substation equipments maintenance and testing system, power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency, and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode, integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS,the field work data of the sub systems are the source information of MIS, by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing, this system is triumphantly using in all 220kV and above substations in Jiangxi grid.

    标签: 电网 信息化 管理系统

    上传时间: 2013-11-15

    上传用户:han_zh

  • PCA9516 5channel I2C hub

    The PCA9516 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both the data(SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF.The I2C-bus capacitance limit of 400 pF restricts the number ofdevices and bus length. Using the PCA9516 enables the systemdesigner to divide the bus into five segments off of a hub where anysegment to segment transition sees only one repeater delay.

    标签: 5channel 9516 PCA I2C

    上传时间: 2013-11-21

    上传用户:q123321

  • PCA9548A 8 channel I2C bus swi

    The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.

    标签: channel 9548A 9548 PCA

    上传时间: 2013-10-13

    上传用户:bakdesec

  • USB Demonstration for DK3200 w

    The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.

    标签: Demonstration 3200 USB for

    上传时间: 2014-02-27

    上传用户:zhangzhenyu

  • Input Signal Rise and Fall Tim

    All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.

    标签: Signal Input Fall Rise

    上传时间: 2013-10-23

    上传用户:copu