针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
介绍一种应用于长城赛弗SUV汽车后门车窗多功能控制器，能实现对电动玻璃车窗、车窗雨刮器、喷水器以及电加热除霜器等控制。介绍了基于NXP P89LPC922单片机多功能汽车后车窗控制器的控制功能、硬件电路原理和软件设计方法。 Abstract: This paper presents a multipurpose automotive rear windows controller for CHANGCHENG SAFE SUV.The controller can control rear power-operated window,rear wiping,washing water pump and rear defroster of the windows. In this paper, it is introduced in detail that the functions and the design of the circuit and program of the controller based on NXP P89LPC922 MCU.
上传时间： 2013-11-13
上传用户：z754970244
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上传时间： 2013-10-23
上传用户：xiehao13
主要介绍构成记忆示波器的STC12C5408AD增强型单片机8通道10位模数转换功能的设置、应用和具体的汇编程序设计，以及PC机串行通讯和图形显示的高速汇编程序的设计要点，并列举实例说明其应用效果。 Abstract: The configuration, applications and the designs for? compiling program of the memorial oscillograph of 10 bits A/D conversation are introduced. It’s bases on STC12C5408AD 8? channels? single-chip? computer? in? enhancement? mode. It also recommends the devising essentials of high speed compiling program for PC serial communication and graphics display, lists examples to explain its effects in using.
上传时间： 2013-10-10
上传用户：adada
详细介绍了TLC1549系列模数转换器的特点及工作原理，然后根据TLC1549的工作时序和A/D转换原理针对实际问题编写了详细的汇编语言程序。 Abstract: A basic principle and characteristic of TLC1549 analog-to-digital converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
上传时间： 2014-07-16
上传用户：blans
介绍一种以MSP430单片机为基础的智能频率测量系统，采用硬件逻辑与软件指令相结合的方式控制闸门，实现0 MHz~10 MHz范围内无档切换的等精度测量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上传时间： 2013-10-28
上传用户：dbs012280
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
介绍基于ATmega8型单片机的温度测量及加热控制系统。分析系统的工作原理，详尽讨论系统的硬件电路和软件流程。实验证明，该系统工作可靠，稳定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
上传时间： 2013-11-21
上传用户：caiguoqing
利用Atmel公司的ATmega168微处理器，采用A/D转换方式来实现按摩椅控制器的键盘接口，通过在硬件电路中巧妙地选择电阻，在软件设计中采用数字滤波、二分法和区间鉴定等方法，灵敏可靠地实现了按摩椅中30个按键的处理。给出了硬件电路设计和软件设计思想以及部分汇编代码。 Abstract: This paper chooses A/D conversion method to realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
上传时间： 2014-01-10
上传用户：咔乐坞
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-09
上传用户：ligi201200
