This a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It permits you to download new code to the device over USB. This bootrom is installed at address 0x00000000 in the ARM, which means that it is the first piece of code to execute after reset. At startup, it waits for a few seconds to see if the downloader is trying to connect. If not, then the bootloader gives up control and jumps to your program. If the downloader is trying to connect, then the bootloader receives the new program over USB and writes it into flash.
标签： bootloader processors download permits
上传时间： 2015-11-30
上传用户：shus521
Universal Serial Bus (USB) is a communications architecture that gives a personal computer (PC) the ability to interconnect a variety of devices using a simple four- wire cable. The USB is actually a two-wire serial communication link that runs at either 1.5 or 12 megabits per second (mbs). USB protocols can configure devices at startup or when they are plugged in at run time. These devices are broken into various device classes. Each device class defines the common behavior and protocols for devices that serve similar functions. Some examples of USB device classes are shown in the following table
标签： communications architecture Universal computer
上传时间： 2015-12-08
上传用户：stvnash
Avalon Interface Specification,The Avalon interface specification is designed to accommodate peripheral development for the system-on-a-programmable-chip (SOPC) environment. The specification provides peripheral designers with a basis for describing the address-based read/write interface found on master and slave peripherals, such as microprocessors, memory, UART, timer, etc.
标签： Avalon Specification specification accommodate
上传时间： 2014-03-06
上传用户：pompey
usb 1.1 规范 The 1.1 revision of the specification is intended for product design. Every attempt has been made to ensure a consistent and implementable specification. Implementations should ensure compliance with this revision.
标签： specification 1.1 revision intended
上传时间： 2015-12-16
上传用户：WMC_geophy
This book is for developers who design and program devices that use the Universal Serial Bus (USB) interface. The goal is to introduce you to USB and to help you get your devices up and communicating as quickly and easily as possible.
标签： developers Universal devices program
上传时间： 2014-09-07
上传用户：sdq_123
This directory contains the memtest 8051 firmware for the Anchor Chips EZ-USB chip. The purpose of this software is to test the different memory segments in the Ez-Usb chip. This example will output the string "good" on the 7 segment LED if the mem test passes, or it will output the first address where the memtest fails.
标签： directory the contains firmware
上传时间： 2013-12-16
上传用户：gdgzhym
// This program measures the voltage on an external ADC input and prints the // result to a terminal window via the UART. // // The system is clocked using the internal 24.5MHz oscillator. // Results are printed to the UART from a loop with the rate set by a delay // based on Timer 2. This loop periodically reads the ADC value from a global // variable, Result.
标签： the measures external program
上传时间： 2013-12-27
上传用户：trepb001
usb bulk 传输例程。 * The bulkusb driver is a generic function driver, based on the Windows Driver Model (WDM). * Supports Plug and Play(PnP), Power Management(PM), Windows Management Instrumentation (WMI) and the Selective Suspend (SS) features. * This sample is based off the selSusp DDK sample. Please refer the selSusp sample and the DDK docs to understand the handling of PnP, PM, WMI and SS features and implementations. * The USB device used for this sample is a generic Intel I82930 USB evaluation board programmed with a simple loopback test using a 64 KB circular buffer. None of the code in the sample is specific to this controller chip.
标签： driver function Windows bulkusb
上传时间： 2016-04-25
上传用户：270189020
NAME: u2440mon.c DESC: u2440mon entry point,menu,download HISTORY: Mar.25.2002:purnnamu: S3C2400X profile.c is ported for S3C2410X. Mar.27.2002:purnnamu: DMA is enabled. Apr.01.2002:purnnamu: isDownloadReady flag is added. Apr.10.2002:purnnamu: - Selecting menu is available in the waiting loop. So, isDownloadReady flag gets not needed - UART ch.1 can be selected for the console. Aug.20.2002:purnnamu: revision number change 0.2 -> R1.1 Sep.03.2002:purnnamu: To remove the power noise in the USB signal, the unused CLKOUT0,1 is disabled.
标签： 2440 mon download purnnamu
上传时间： 2016-05-12
上传用户：wff
This project shows how to use the IOKit notification mechanism to register to be notified when devices come and go. It uses the Cypress/Anchor EZ-USB chip. (Look at the following example for another way to get notified when a device is unplugged).
标签： notification mechanism notified register
上传时间： 2013-12-01
上传用户：zhuimenghuadie
