The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上传时间： 2013-11-16
上传用户：浩子GG
CAT5110/18/19/23/24/25 linear-taper digitally programmable potentiometers perform the same function as a mechanical potentiometer or a variable resistor. These devices consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a2-wire up/down serial interface.
上传时间： 2013-11-22
上传用户：541657925
This document describes the system hardware implementation for the OMAP3530 processor and theTPS65930/20 companion power integrated circuit (IC). The document concentrates on the powerconnectivity for the processor and the companion power IC. The document also briefly explains someother specifics related to power, such as the boot modes and the power-up sequence.
上传时间： 2013-11-14
上传用户：yeling1919
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
上传时间： 2013-11-07
上传用户：xy@1314
The PAM2862 is a continuous mode inductivestep-down converter, designed for driving singleor multiple series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
上传时间： 2013-11-16
上传用户：司令部正军级
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上传时间： 2013-11-24
上传用户：Alick
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The TJA1042 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing the differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1042 TJA
上传时间： 2014-12-28
上传用户：气温达上千万的
The outputs of the PCA9518 are immediately available as soon as there is a voltage present on thesupply >~1V and behave as described above. The power-on reset of the PCA9518A keeps the outputsturned off during power-up and maintains the high impedance of the outputs throughout the power-upcycle. There is an additional built-in delay after power-up that allows the analog circuits to stabilize beforethe part is activated.
标签： Replacement 9518 NXP PCA
上传时间： 2013-10-26
上传用户：13817753084
