Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上传时间： 2014-01-18
上传用户：wenyuoo
毕业设计 USB TO Gigabit LAN 网卡 随着网络技术飞速发展，多媒体的应用越来越多，人们对网络的要求也越来越高，为了适应市场的需求，网卡出现了。它以其结构简单、成本低廉、兼容性强等诸多的优越性得到了广泛的应用。由于网络的应用越来越广泛，网卡的应用也越来越多、功能越来越强大。开始时由于技术方面的限制，网卡只有10Mbps的吞吐量，由于网络技术的发展，100Mbps吞吐量的网卡开始在市场上得到广泛的应用。而现在1000Mbps吞吐量的网卡的出现又给网络的传输带来了新的活力。 论文中主要阐述了基于以太网的USB TO Gigabit LAN网卡的设计与制作。论文首先对以太网进行了介绍，紧接着讲了网卡的基本知识。随后又对USB TO Gigabit LAN网卡的电路设计和制作进行了详细的描述。论文还包括了USB TO Gigabit LAN网卡的调试等内容。
上传时间： 2014-12-02
上传用户：wab1981
在嵌入式系统中，嵌入式CPU往往要通过各种串行数据总线与“外界”进行通信。在应用中，异步的串行数据通信用得较多，而通用异步收发器UART（Universal Asynchronous Receiver Transmitter）在其中扮演着重要角色：完成数据的串并转换，即把并行数据按照通信波特率转化为通信协议中规定的串行数据流，也可从串行数据流中取出有用数据转变为并行数据。而UART与CPU接口简单，CPU只需通过执行读写操作即可完成收发数据，从而完成与外界的通信。有许多现成的芯片可以实现UART的功能，如常用的Intel8250/8251接口芯片就可以作为RS232、RS422串口的UART控制芯片。
上传时间： 2013-11-25
上传用户：www240697738
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上传时间： 2013-11-01
上传用户：ghostparker
There is no doubt that remote controls are extremely popular and it has become very hard to imagine a world without them. They are used to control all manner of house appliances like the TV set, the stereo, the VCR, and the satellite receiver.
上传时间： 2013-11-13
上传用户：顶得柱
