The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog Switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these Switches combine high-voltage bilateral MOSSwitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上传时间： 2013-10-09
上传用户：yepeng139
Abstract: IC Switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-acquisition systems.
上传时间： 2013-11-12
上传用户：acwme
TCS ECN Background & Key TermsTrust Issues with PCIe PlatformsTCS ECN DetailsTrusted Config Space and TCS TransactionsTrusted Config Access Mech (TCAM)Standard vs Trusted Config AccessNew Capability StructuresTCS Support in Root Ports, Switches, & BridgesTCS “Does not…” ListExample Trusted Computing PlatformRevisiting the Trust IssuesKey Takeaways/Call to ActionQuestions
标签： Configuration Trusted PCIe Spa
上传时间： 2013-11-21
上传用户：hsfei8
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET Switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power Switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上传时间： 2013-10-22
上传用户：ztj182002
An essential component of a noise-free audio device isa clean power supply, but few switching regulators canoperate at high efficiency while keeping the switchingfrequency out of the audio band. The LTC®3620 fills thisvoid. It is a high efficiency 15mA buck regulator with aprogrammable minimum switching frequency, making itpossible to virtually eliminate audible switching noise. Theinternal synchronous Switches and low quiescent currentof this buck regulator provide the ability to maintain highefficiency, while its small footprint makes it ideal for tiny,low power audio applications.
上传时间： 2013-10-21
上传用户：非衣2016
The PCA9536 is an 8-pin CMOS device that provides 4 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. I/O expanders provide a simple solution when additional I/O is needed for ACPI power Switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-10-27
上传用户：w230825hy
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power Switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-11-17
上传用户：vodssv
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context Switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [via macros]• Trace visualisation ability (requires more RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
上传时间： 2013-10-13
上传用户：13162218709
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power Switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-10-10
上传用户：inwins
